Bedienungsanleitung Scholtes lvti 1267 (Seite 19 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch)

123784

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

 Only use products that have been specifically designed

for dishwashers.

Do not use table salt or industrial salt.

 If using a multi-functional product (2-in-1, 3-in-1, 4-in-1, etc..) it

is not necessary to add rinse aid; however, we recommend

that you add salt, especially if you live in an area where the

water is hard or very hard. If you do not add salt or rinse aid,

the LOW SALT* and LOW RINSE AID* indicator lights will

flash continuously.

Loading the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

• whenever the indicator light (H) signals that it is empty.

Illuminated light: add rinse aid; unlit light: there is no

shortage of rinse aid in the dispenser.

• when the LOW RINSE AID* indicator light on the panel

flashes;

1. Open the dispenser by

turning the lid (G) in an

anticlockwise direction.

2. Pour in the rinse aid, making

sure it does not overflow from

the dispenser. If this happens,

clean the spill immediately with a

sponge.

3. Screw the lid back on.

NEVER pour the rinse aid

directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the washing or

drying results, you may adjust the quantity of rinse aid

used. Use a screwdriver to turn the dosage adjuster to one

of the 6 pre-set positions (the default position is set to 4):

• if there are bluish streaks on the crockery, set the

adjuster to a lower number (1-3).

• if drops of water remain on the crockery or there are

limescale marks present after the cycle has finished, set

the adjuster to a higher number (4-6).

 If you are using multi-functional tablets (2-in-1, 3-in-1, 4-in-1,

etc..) and you wish to further improve the drying

performance of the appliance, fill the dispenser and set the

dosage adjuster to 2.

Loading the refined salt

In order to obtain the best possible results from a wash

cycle, make sure that the dispenser is never empty. Refined

salt removes limescale from the water, thus avoiding the

formation of deposits on crockery. The salt dispenser is

located in the lower part of the dishwasher (

see

Description

) and should be filled:

• when the green float* cannot be seen by simply looking

at the cap of the salt dispenser;

• when the LOW SALT* indicator light on the panel flashes;

• if your machine is not equipped with an indicator light

a green float:

approximately every 30 wash cycles;

1. Remove the lower rack and

unscrew the cap of the dispenser

(in an anti-clockwise direction).

2. For the first wash cycle only: fill

the dispenser up to the edges with

water.

3. Position the funnel provided

correctly (

see figure

) and fill the

salt dispenser up to the edges (approximately 2 kg); it is

normal for a little water to leak out.

4. Remove the funnel, wipe away any salt residue from the

thread and screw the cap on tightly, so that detergent does

not leak into the dispenser during the wash cycle (this could

damage the water softening system beyond repair).

 When salt has been added, run a wash cycle immediately,

without crockery, in order to remove any salt solution that

has leaked out and to avoid corrosion.

Adjusting the amount of salt*

It is possible to adjust the amount of salt used according to

the hardness of the water in your area (this information is

available from your local water board).

1. Unscrew the dispenser cap.

2. Turn the arrow on the neck of the

dispenser (

see figure

) towards the + or -

symbols, using the table below as a

guide.

The default setting of the water softening system is +.

- If using multi-functional tablets (2-in-1, 3-in-1, 4-in-1, etc...) fill

the salt dispenser and set the adjuster to -; if the hardness of

the water is greater than 60°fH, set it to +.

* Only available in selected models.

Rinse aid and refined salt

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes lvti 1267 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scholtes lvti 1267

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info