Bedienungsanleitung Scholtes lvti 1267 (Seite 17 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

123784

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Turning on the Appliance

Starting a wash cycle....

After performing all the operations described in the previous

paragraphs, turn the water tap on completely, open the

appliance door and press ON-OFF button "A": indicator light

"B" comes on. Your appliance is now on and awaiting

instructions.

Setting and Starting a Wash Cycle

Select the wash cycle by pressing button "P". Each time this

button is pressed, one of the indicator lights "M" will come

on in sequence, select the wash cycle you deem most suitable

for the type of dishes to wash (take a look at page 17, where

you will find the wash cycle table). Close the appliance door

and after a few seconds, you will hear a short beep: the

wash cycle has begun."

Cancelling or modifying a cycle while underway...

Premise: You can cancel the wash cycle in progress, if it has

only just started.

But if you have chosen the wrong cycle, not to worry! You

can modify the wash cycle in progress, if it has only just started.

Open the appliance door carefully to avoid any hot water

splashes, then keep button "P" pressed for approximately 5

seconds, until you hear 3 short beeps. Indicator light "M"

will come off and at this point, all the settings will have been

cancelled. You are now free to re-set the correct wash cycle.

If you forget to load some of the dishes...

Well, it happens to everyone. Interrupt the wash cycle by

opening the appliance door with the utmost care, as usual,

then insert the dish you had forgotten. When you shut the

appliance door, the cycle will start up from where you

interrupted it.

At the end of the wash cycle...

The end of the wash cycle is indicated by a double beep and

the flashing of the wash cycle indicator light "M".

Turn off the water tap.

Wait a few minutes before unloading the dishes: they are

very hot! If you wait a little while, they dry better thanks to

the steam.

Empty the lower rack first.

Make sure the wash cycle has ended before removing the

dishes!

Warning:

If opening the door soon after the end of the programme, or

during it, stand away from the Dishwasher, to avoid possible

injury from hot steam.

There's been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity

comes back on or when you close the door.

Do you want extra drying?

Press button "E" before you start the selected wash cycle.

A prolonged beep will inform you that you have selected

extra drying, a short beep indicates it has been disabled.

With extra drying, the wash cycle will last longer, to provide

you with drier dishes.

Setting The Start Delay Time

When you have loaded the dishes, you can choose when to

start your dishwasher before setting the desired wash cycle.

Press button "C" to delay the start of the wash cycle by 6, 4

or 2hours. Each time you press it, you will hear a short beep

and indicator light "D" corresponding to the selected delay

will come on.

Now you can select the desired wash cycle. Close the

appliance door and, after you hear the beep, the countdown

to the delayed start will begin.

Once this time is up, the indicator light will stop flashing and

the wash cycle will begin.

If you change your mind and you wish to set a different

delay, just open the appliance door, press button "C" and

repeat the selection.

If, on the other hand, you want to cancel the delayed start

set and you want the wash cycle to start immediately, press

the button repeatedly until indicator light "D" comes off.

When you close the appliance door, the wash cycle starts up

and a short beep sounds.

If the power to the appliance goes off or the door is opened

during the delay period, the clock will stop the countdown. It

will start again when the power has come back on, or when

the door has been closed.

You want to wash on one rack only?

Remember to use half the amount of detergent.

Your dishwasher also allows you to wash half a load, to save

water and electricity. Before setting any wash cycle

whatsoever, press button "Q" repeatedly to select whether

you want to run a half cycle on the upper or lower rack.

Each time you press it, you will hear a short beep and indicator

light "R" corresponding to the selected rack will come on.

Warning!

Open the dishwasher door, turn off by pressing button

“A”, unplug the appliance from the electricity socket to

cut off the power supply; the power supply cable should

consequently be easily accessible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes lvti 1267 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scholtes lvti 1267

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info