Bedienungsanleitung Scholtes lvx 12 56 wh (Seite 19 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

126890

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Turning on the Appliance

How to start a wash cycle

Insert the plug into the electricity socket to power the

dishwasher. Turn on the water tap completely and press ON-

OFF button "A"; the display lights up and the wash cycle

time selected on the knob will flash.

Starting and setting the cycle.

Turn the cycle selector "M" until the reference notch on the

knob corresponds with the symbol or number of the cycle

you wish to set (consult the wash cycle table contained in

this manual, especially when first using the appliance).

After a few seconds, a beep indicates the wash cycle has

started and indicator "G" displays the symbol corresponding

to the phase with which it has begun. The counter "L" will

indicate the estimated amount of time left until the end of

the wash cycle.

Do not expect a precise countdown as the wash cycle starts

with an estimated cycle time that is updated as the cycle

progresses and according to a number of parameters that

affect the cycle itself (such as water hardness, the tempera-

ture of the water, the degree of soil, etc.).

You want to wash on one rack only? Remember to use

half the amount of detergent.

If you only have a few dishes to wash, you can load these

onto one rack only, saving on both water and electricity.

Press button "I", a beep will sound and indicator "N" appears

on the display. Each time you press the button, a beep will

sound and symbol corresponding to the upper rack or

symbol corresponding to the lower rack will appear. If

you press the button once more, the selection will be reset

and the dishwasher will consequently wash on both racks.

To use the racks correctly, we recommend you read the

chapter entitled "Loading the dishes".

Cycle phase under way indicator

Your dishwasher is equipped with an indicator "G" comprising

4 symbols which represent the different phases of a wash

cycle. When the wash cycle has started, the display will indi-

cate the phases under way in sequence.

These phases are:

pre-wash wash rinses drying

Cancelling and modifying a wash cycle in progress

Premise: a wash cycle in progress can only be modified if it

hasn't been running for long.

To modify it, turn the knob and set it to RESET. After a few

seconds, you will hear 4 beeps, indicator "G" relating to the

phase under way will turn off and 3 dashes will appear. At

this point, all the settings will have been cancelled.

To select a new wash cycle, repeat the instructions contained

in the paragraph entitled "Starting and setting the cycle".

You've left out a dish?

You can interrupt a wash cycle by pressing the "ON-OFF"

button, then place the forgotten dishes into the appliance,

which will start up from where it was interrupted when you

turn it back on.

There's been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity

comes back on or when you shut the door.

How to programme extra drying.

If you want your dishes to be perfectly dry, follow the

instructions below.

Set the knob to RESET and make any specific settings, such

as:

- upper or lower rack

- delayed start

Start the wash cycle by turning the knob and open the

appliance door. Observe symbol for drying: it will flash

for about 4 seconds, while the word "OFF" appears on the

display (extra drying disabled).

If you press button "I" immediately, you will hear a prolonged

beep and the word "ON" will appear on the display: the

extra drying has been enabled.

Once you have made your selection, shut the appliance door;

a beep will sound and the wash cycle will either start

immediately or after the delay, wherever set.

Remember that with extra drying, the wash cycle will last

longer, to provide you with drier dishes.

At the end of the wash cycle

At the end of the wash cycle, 2 beeps are sounded and the

word END flashes. Bring the selector back to the RESET

position, and the 3 dashes for programming cancellation will

appear.

Turn off the water tap and open the door.

Wait a few minutes before removing the dishes: this way

you won't have to handle them while they're still hot and

they will dry better.

Empty the bottom rack first.

Make sure the wash cycle has ended before removing the

dishes!

Warning:

Turn the display off by pressing button “A”, unplug the

appliance from the electricity socket to cut off the power

supply; the power supply cable should consequently be

easily accessible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes lvx 12 56 wh Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info