Bedienungsanleitung Scholtes tt 6054 (Seite 15 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

331268

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

UNDERSIDE OF HOB

L N

1 2 3 4 5

Blue

Brown

Neutral

Live

Green/Yellow

Earth

U-bolt

connection support

Phase Neutral Earth

The thickness of the supporting surface should be taken

into account when choosing screws for the fixing hooks:

 30 mm thick: 17.55 mm screws

 40 mm thick: 7.55 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment

springs in the holes provided in the centre of each side

of the hob.

2. Insert the hob in the cavity, make sure it is in a central

position and push down on the whole perimeter until the

hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob into

its cavity, insert the 4 fixing hooks (each has its own pin)

into the lower edges of the hob, using the long pointed

screws to fix it in place, until the glass is stuck to the

supporting surface.

! The screws for the alignment springs must remain

accessible.

! In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it

has been installed.

! All parts that ensure the safe operation of the appliance

must not be removable without the aid of a tool.

Electrical connection

! The electrical connection of the hob and any built-in

oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

Terminal board

On the lower part of the

appliance there is a connection

box for the different types of

electricity supply (the picture is

only an indication and is not an

exact representation of the

purchased model).

Single-phase connection

! The cable provided should only be used for this type of

installation.

Mains supply characteristics:

Voltage and mains frequency

 230/240V 1+N ~ 50 Hz

 230V 2 ~ 50 Hz

If the hob has a supply cable fitted,

connect it to the mains, using the

colours as a guide (see diagram).

If the hob does not have a supply cable fitted, proceed

as follows:

1. Use the supply cable provided (where applicable) or

a suitable supply cable, H05VV-F or higher, with the right

dimensions (cable section: 2.5 mm).

2. To open the terminal board, insert a screwdriver into

the side tabs of the cover (see Terminal board picture).

3. The terminal board is designed for single-phase

connection: make sure the connection supports between

springs 1 and 2 and those between 4 and 5 are in the

right position (see Single-phase picture).

4. Position the wires according to the following diagram

and table and connect the appliance by tightening all

the screws for the springs as much as possible.

Single-phase

5. Secure the power supply cable by fastening the

clamp screw then put the cover back on.

Voltage and

mains

frequency

Electrical connections

Terminal

board

230/240V 1+N ~

50 Hz

230V 2 ~ 50 Hz

Single-

phase

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes tt 6054 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scholtes tt 6054

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info