Bedienungsanleitung Scholtes tt 6054 (Seite 16 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

331268

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Other types of connection

! The cable provided is not suitable for the following

types of installation.

If the mains supply corresponds with one of the

following:

Voltage and mains frequency

 400V 3 - N ~ 50 Hz

 400V 2 - N ~ 50 Hz

 230V 3 ~ 50 Hz

 230V 2 + 2 - N ~ 50 Hz

proceed as follows:

1. Use a suitable supply cable, H05RR-F or higher, with

the right dimensions (cable section: 1.5 mm).

2. To open the terminal board, insert a screwdriver into

the side tabs of the cover (see Terminal board picture).

3. Loosen the cable clamp screw and the terminal board

screws according to the type of connection required and

position the connection supports as shown in the

following table and diagrams.

4. Position the wires according to the following table and

diagrams and connect the appliance by tightening all

the screws for the springs as much as possible.

5. Secure the power supply cable by fastening the

clamp screw then put the cover back on.

Connecting the supply cable to the mains

If the appliance is being connected directly to the mains

an omnipolar circuit-breaker must be installed with a

minimum opening of 3 mm between contacts.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant with

safety regulations.

Before connecting to the power supply, make sure that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of the

appliance, which is indicated on the attached data

plate.

 The voltage is in the range between the values

indicated on the data plate.

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the plug,

ask an authorised technician to replace it. Do not use

extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only.

! The manufacturer declines any liability should these

safety measures not be observed.

N2N1

1 2 3 4

L1 L2 L3

1 2 3 4 5

L1 L2 N

1 2 3 4 5

Phase

Neutral

EarthPhase

Neutral

U-bolt

connection support

U-bolt

connection support

Phase PhasePhase Neutral Earth

Phase Neutral

U-bolt

connection support

Earth

Phase

Phase Phase

U-bolt

connection support

Earth

Phase

L1 L2 L3 N

1 2 3 4 5

Two-phase

Three-phase 400

Three-phase 400 2+N

Three-phase 230

Voltage and

mains

frequency

Electrical connections

Terminal

board

400V 3-N ~

50 Hz

Three-phase

400

400V 2-N ~

50 Hz

Three-phase

400 2+N

230V 3 ~ 50 Hz

Three-phase

230

230V 2+2-N ~

50 Hz

Two-phase

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes tt 6054 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scholtes tt 6054

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info