Bedienungsanleitung Schwinn 130i (Seite 22 von 36) (Englisch)

671371

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

OPERATIONS

What to Wear

Wear rubber-soled athletic shoes. You will need the appropriate clothes for exercise that allow you to move freely.

How Often Should You Exercise

Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in your chest,

become short of breath, or feel faint. Contact your doctor before you use the machine again. Use the values calculated

or measured by the machine’s computer for reference purposes only. The heart rate displayed on the console is an

approximation and should be used for reference only.

• 3 times a week for 30 minutes each day.

• Schedule workouts in advance and try to follow the schedule.

Seat Adjustment

Correct seat placement encourages exercise efﬁciency and comfort, while reducing the risk of injury.

1. With a Pedal in the forward position, center the ball of your foot over the center of it. Your leg

should be bent slightly at the knee.

2. If your leg is too straight or your foot cannot touch the Pedal, move the seat down on the upright

bike. If your leg is bent too much, move the seat up.

Step off the bike before you adjust the seat.

Loosen and pull the adjustment knob on the seat tube. Adjust the seat to the desired height. Release

the adjustment knob to engage the locking pin. Be sure that the pin is fully engaged and fully tighten

the knob.

Do not set the Seat Post position higher than the stop mark (STOP) on the tube.

Foot Position / Pedal Strap Adjustment

Foot pedals with straps provide secure footing to the exercise bike.

1. Put the ball of each foot on the Pedals.

2. Rotate the Pedals until one can be reached.

3. Fasten the strap over the shoe.

4. Repeat for the other foot.

Be sure toes and knees point directly forward to ensure maximum Pedal efﬁciency. Pedal straps can

be left in position for subsequent workouts.

Power-Up / Idle Mode

The Console will enter Power-Up / Idle Mode if it is plugged into a power source, any button is pushed, or if it receives a signal

from the RPM sensor as a result of pedaling the machine.

Auto Shut-Off (Sleep Mode)

If the Console does not receive any input in approximately 5 minutes, it will automatically shut off. The LCD display is off while

in Sleep Mode.

Note: The Console does not have an On/Off switch.

Initial Setup

During the ﬁrst power-up, the Console should be setup with the date, time and your preferred measurement units.

1. Date: Push the Increase/Decrease buttons to adjust the currently active value (ﬂashing). Push the Left/Right buttons to

change which segment is the currently active value (month / day / year).

2. Push OK to set.

3. Time: Push the Increase/Decrease buttons to adjust the currently active value (ﬂashing). Push the Left/Right buttons to

change which segment is the currently active value (hour / minute / AM or PM).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Schwinn 130i Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Schwinn 130i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info