Bedienungsanleitung Schwinn 530 - 2017 (Seite 49 von 50) (Englisch)

737320

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Condition/Problem Things to Check Solution

Console shuts off (enters

sleep mode) while in use

Check electrical (wall)

outlet

Make sure unit is plugged into a functioning wall outlet. Test the

outlet with a known functioning device such as a lamp.

Check connection at front

of unit

Connection should be secure and undamaged. Replace

adapter or connection at unit if either are damaged.

Check data cable integrity All wires in the cable should be intact. If any are cut or crimped,

replace cable.

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly.

Small latch on connector should line up and snap into place.

Reset machine Unplug unit from electrical outlet for 3 minutes. Reconnect to

outlet.

If the above steps do not resolve the problem, contact your lo-

cal distributor for further assistance.

Fan will not turn on or will

not turn off

Reset machine Unplug unit from electrical outlet for 5 minutes. Reconnect to

outlet.

Fan will not turn on, but

Console operates

Check for blockage of fan Unplug unit from electrical outlet for 5 minutes. Remove mate-

rial from fan. If necessary, detach the Console to help with

removal. Replace the Console if unable to remove blockage.

Thumping sound when

belt operates

Walking belt Walking belt needs to be used for wear in period. Sound will go

away after the wear in period.

Unit rocks/does not sit

level

Check leveler adjustment Adjust levelers until machine is level.

Check surface under unit Adjustmentmaynotbeabletocompensateforextremelyun-

even surfaces. Move machine to level area.

Walking belt not aligned Machine leveling Make sure the machine is level. Refer to the procedure for

leveling the machine in this manual.

Walking belt tension and

alignment

Make sure the walking belt is centered and tension is correct.

Refer to the procedures for adjusting tension and aligning the

belt in this manual.

Motor sounds strained Silicone lubrication on

walking belt

Apply silicone to the inner surface of the walking belt. Refer to

the belt lubrication procedure in this manual.

Hesitation or walking belt

slips when in use

Belt tension Adjust the belt tension at the rear of the machine. Refer to the

procedure for adjusting belt tension in this manual.

Belt stops moving while

in use

Safety key Plug Safety Key into Console. (See Emergency Stop Proce-

dure in the Important Safety Instructions section.)

Motor overload Unit may be overloaded and draw too much current, which

causes power to turn off to protect motor. Refer to maintenance

schedule for belt lubrication. Make sure the walking belt tension

is correct, and start unit again.

If the above steps do not resolve the problem, contact your lo-

cal distributor for further assistance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Schwinn 530 - 2017 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Schwinn 530 - 2017

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info