Bedienungsanleitung Schwinn IC8 (Seite 23 von 28) (Englisch)

737637

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Read all maintenance instructions fully before you start any repair work. In some conditions, an assistant is required to do

the necessary tasks.

Equipment must be regularly examined for damage and repairs. The owner is responsible to make sure that

regular maintenance is done. Worn or damaged components must be repaired or replaced immediately.

Only manufacturer supplied components can be used to maintain and repair the equipment.

If at any time the Warning labels become loose, unreadable or dislodged, replace the labels. If purchased

in US/Canada, contact Customer Service for replacement labels. If purchased outside US/Canada, contact

your local distributor for them.

Disconnect all power to the machine before you service it.

Daily: Before each use, examine the exercise machine for loose, broken, damaged, or worn parts. Do not

use if found in this condition. Repair or replace all parts at the rst sign of wear or damage. Make

sure adjustment knobs are tight. Tighten as necessary. After each workout, use a damp cloth to

wipe your machine and Console free of moisture.

NOTICE: If necessary, only use a mild dish soap with a soft cloth to clean the Console. Do not

clean with a petroleum based solvent, automotive cleaner, or any product that contains

ammonia. Do not clean the Console in direct sunlight or at high temperatures. Be sure to

keep the Console free of moisture.

Weekly: Clean the machine to remove any dust, dirt, or grime from the surfaces.

Check for smooth seat operation. If needed, sparingly apply a thin coating of silicone lube to ease

operation.

Silicone lubricant is not intended for human consumption. Keep out of reach of

children. Store in a safe place.

Note: Do not use petroleum based products.

Monthly

or after 20

hours:

Check pedals and crank arms and tighten as necessary. Make sure all bolts and screws are tight.

Tighten as necessary.

Check the drive belt tension and adjust if necessary.

Checking the Drive Belt Tension

To check the Drive Belt tension, the bike needs to be operated. Get the pedals rotat-

ing at about 20 RPM. Then suddenly increase the RPM to your maximum ability. If the

pedals move normally with no slipping, the tension is correct. If the Pedals slip, the belt

needs to be adjusted.

Adjusting the Drive Belt Tension

1. To change the tension of the Drive Belt, loosen the Axle Nuts. Use a 15mm open

end wrench to hold the Axle Nut on one side steady, and loosen the Axle Nut on

the opposite side with a 15mm socket and wrench.

2. If the Drive Belt is too loose and slipping, use a 10mm wrench to turn each Fly-

wheel Retainer Nut a 1/4 turn to the right (clockwise).

3. Re-test the tension of the Drive Belt, and adjust if still necessary.

A detailed “Adjust the Belt Tension” procedure can be found in the Service Manual.

MAINTENANCE

Flywheel Retainer Nuts

Axle Nut

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Schwinn IC8 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Schwinn IC8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info