MOUNTAIN BIKE AND MOUNTAIN BIKE-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2017ORIGINAL OPERATING INSTRUCTIONS 2017 | MOUNTAIN BIKE AND MOUNTAIN BIKE-PEDELEC
| 68
bcaefd
To measure the travel you can use the rubber ring mainly located on the thinner,
plunging tube of the suspension fork. If there is no rubber ring, tie up a cable tie
around one of the stanchion tubes. Make sure it is not too tight, you should still
be able to move it, it should however not slip by itself.
Put on your usual riding clothing (including if necessary a packed rucksack),
sit on your bike and bring yourself into the usual riding position. Lean against a
fixed object (railings, wall etc.) and make sure you do not fall over. Ask a helper
to move the rubber ring or the cable tie downwards against the dust seal at the
lower leg.
Get off your SCOTT bike so that the fork does not compress any more. The dis-
tance between the rubber ring/cable tie and the wiper is the negative suspen-
sion travel, or sag (d). Compare it with the total suspension travel (as specified
by the manufacturer) to determine whether the suspension should be set to be
harder or softer.
With pneumatic suspension forks the spring rate is set by the air pressure in
the fork. The pressure must be set before the first ride by means of a special
high-pressure pump with pressure gauge (e) and modified later as required due
to changes in the weight of the rider and/or load.
Note the appropriate setting values and check them subsequently at regular
intervals. Always follow the recommendations of the manufacturer and never
exceed the maximum air pressure for the suspension fork. Always make a test
ride after each change to the settings.
In the case of most suspension forks with coil springs a preload can be applied
to the springs within tight limits by turning a knob at the top of the fork crown
(f). If that is not possible and the desired negative suspension travel (“sag”)
cannot be set, the coil springs must be replaced by harder or softer models. The
replacement is a job for the SCOTT dealer.
When replacing any parts, be sure to only use parts that bear the appropriate
mark and, to be on the safe side, original spare parts. Your SCOTT dealer will be
pleased to help you.
FRONT SUSPENSION
Most of the SCOTT mountain bikes (a) and SCOTT pedelecs (b) have suspen-
sion forks. This feature gives you better control of your SCOTT bike when riding
cross-country or on rough road surfaces and ensures more ground contact for
the tyre. It noticeably reduces the strain on you and your bicycle caused by the
mechanical shocks from the terrain.
Suspension forks differ in their types of spring elements and damping. Suspen-
sion forks normally work with air spring elements or less often with coil springs.
Damping is usually done by oil.
NOTE!
I
Suspension fork manufacturers normally include instructions with their
deliveries. Read them carefully before changing any settings or doing any
maintenance work on your suspension fork. You can find the instruction of the
suspension fork manufacturer on this SCOTT info CD.
NOTE!
I
For more information see the suspension glossary heading this chapter.
Adjusting the spring rate
To work perfectly, the suspension fork has to be adjusted to the weight of the
rider, the sitting posture and the intended use. Be sure to have this adjustment
carried out by your SCOTT dealer at the time of delivery.
Note in general that the suspension fork must give in a little even when you are
just sitting on the bike – this is the so-called negative suspension travel or sag
(c). When the front wheel passes through a depression in the ground, the spring
extends and the suspension fork will smooth out the uneven surface. If the air
pressure or the spring preload is too high, this effect is lost because the suspen-
sion fork is already fully extended. This means that an important comfort and
safety factor is lost if the tyre briefly loses contact with the ground.
In general, cross-country and marathon racers prefer a shorter negative suspen-
sion travel (sag), whereas freeriders or downhillers riding often in rough terrain
prefer a longer one.. In the case of SCOTT cross-country and SCOTT marathon
bikes the suspension fork should yield by 15-25 % of the maximum suspension
travel, in the case of SCOTT all mountain, SCOTT enduro and SCOTT freeride
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Scott MTB - 2016 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
