MOUNTAIN BIKE AND MOUNTAIN BIKE-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2017ORIGINAL OPERATING INSTRUCTIONS 2017 | MOUNTAIN BIKE AND MOUNTAIN BIKE-PEDELEC
| 76
bcaefd
To measure the travel you can use the rubber ring (b) mainly located on the
thinner, plunging tube of the rear shock. If there is no rubber ring, tie up a cable
tie around one of the thin tube. Make sure it is not too tight, you should still be
able to move it, it should however not slip by itself.
Put on your usual riding clothing (including if necessary a packed rucksack),
sit on your SCOTT bike and bring yourself into the usual riding position. Lean
against a fixed object (railings, wall etc.) and make sure you do not fall over. Ask
a helper to move the rubber ring or the cable tie downwards against the dust
seal at the lower leg.
Get off your SCOTT bike so that the rear frame does not compress any more.
The distance between the rubber ring/cable tie and the wiper is the negative
suspension travel, or sag (c). Compare it with the total spring travel (manufac-
turer specifications) of the rear shock, not rear frame, or measure as a reference
point the straight and smooth area which compresses (c) to determine whether
the suspension needs harder or softer setting.
In the case of air spring rear shocks the spring rate is set by means of the air
pressure in the rear shock (d). The pressure must be set before the first ride by
means of a special high-pressure pump with pressure gauge and modified later
as required due to changes in the weight of the rider and/or load.
Note the appropriate setting values and check them subsequently at regular
intervals. Always follow the recommendations of the manufacturer and never
exceed the maximum air pressure for the rear shock. Always make a test ride
after each change to the settings.
In the case of most rear shocks with coil springs a preload can be applied to the
springs within tight limits by turning a knob (e). If that is not possible and the
desired negative suspension travel (“sag”) cannot be set, the coil spring must be
replaced by a harder or softer model. The replacement is a job for your SCOTT
dealer.
When replacing any parts, be sure to only use parts that bear the appropriate
mark and, to be on the safe side, original spare parts. Your SCOTT dealer will be
pleased to help you.
Make sure the valve is always protected with the valve cap (f) during use.
What to bear in mind when adjusting the seating position
According to the rear shock adjustment the saddle can tilt a little backwards.
Keep this in mind when adjusting the saddle tilt. If you have trouble sitting, try
lowering the nose of the saddle a little compared to your usual position.
For dirt, freeride and downhill use the saddle is often set to a very low position
and tilted backwards.
NOTE!
I
Full suspension SCOTT bikes have a greater ground clearance than bicycles
without rear suspension. If the saddle is adjusted to its proper height you
will normally not be able to reach the floor with your feet. Set the saddle a little
lower to begin with and practise getting on and off the saddle.
Adjusting the spring rate
To work perfectly, the rear shock has to be adjusted to the weight of the rider,
the sitting posture and the intended use. Be sure to have this adjustment carried
out by your SCOTT dealer at the time of delivery.
Note in general that the rear frame must give in a little even when you are just
sitting on your SCOTT bike – this is negative suspension travel, also referred to
as sag (a). If you ride over a pothole the spring is decompressed and the rear
frame compensates for the unevenness. If the air pressure or the spring preload
is too high, this effect is lost because the rear frame is already fully extended.
This means that an important comfort and safety factor is lost if the tyre briefly
loses contact with the ground.
In general, cross-country and marathon racers prefer a shorter negative suspen-
sion travel (sag), whereas freeriders or downhillers riding often in rough terrain
prefer a longer one. In the case of SCOTT cross-country and SCOTT marathon
bikes the rear frame should yield by 10-20 % of the maximum suspension travel,
in the case of SCOTT all mountain, SCOTT enduro and SCOTT freeride bikes by
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Scott MTB - 2016 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
