Bedienungsanleitung Scott Plasma 5 - 2015 (Seite 9 von 13) (Englisch)

664188

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

PLASMA 5 | BIKE OWNER’S MANUAL 2015 BIKE OWNER’S MANUAL 2015 | PLASMA 5

ENGLISH

STEM/HANDLEBAR

Front & Rear Brake Cable Housing:

Cut the front brake cable housing to 35cm length. The final housing length may need

to be trimmed, based on the brand of brake levers.

Cut the rear brake cable housing to 150cm length. The final housing length will need

to be trimmed during the rear brake installation.

Run the front brake cable backward inside the front brake cable housing. Install the

front cable housing, from the rear side of the handlebar through the handlebar exit

hole, by first running the brake cable through the handlebar, then pushing the cable

housing through. The cable can be used to help pull the housing through as well.

Repeat for the rear cable housing, but through the top of the handlebar exit hole, at

the rear side of the handlebar. Make sure the cable housings stick out at the brake

lever end by about 50mm to engage the cable housing slot in the brake lever.

Front Derailleur (FD) & Rear Derailleur (RD) command wires:

IMPORTANT

for electronic shifting Route the front & rear command lever wires through the

handlebar Basebar long holes and out through the spacer base long holes. Do not

assemble the levers yet.

Front Derailleur & Rear Derailleur TT Extension Shifters:

route the Front Derailleur Shifter (Left hand side) wire through the extension slot and

route the wire out through the extension rear end. Connect the wire with a junction

box SM-JC40/41 and connect a COMMAND wire (approx. 150mm) with the junction

boxes SM-JC40/41.

Route the wire out from the side slot or from the rear part of the extension.

Repeat the process for the Rear Derailleur Shifter.

Handlebar/Stem assembly:

route the front brake cable housing through the stem (301A/B) M10 threaded hole.

Route the rear brake cable housing and the Front & Rear Derailleur COMMAND wires

through the stem body upper slot.

Position the handlebar on the stem body handlebar interface and pull gently the

cable housings and wires meanwhile to make sure they do are not bent or pinched

during the assembly.

IMPORTANT

Position the stem top cap over the handlebar: pay attention to the stem top

cap direction! The gap between stem body and stem cap should be approx.

3mm. If the gap is smaller than 2mm, the cap is in the wrong direction and

should be turned backside-front.

Position the four M5 head sunk screws (304) in their respective recesses and tighten

them to the specified torque (T2).

Once the Basebar brake levers are assembled cut the front brake cable housing so

that 25mm stick out of the stem M10 threaded hole and place a cable housing end

cap at the end of the cable housing.

IMPORTANT

Position the brake stop part (305) and tighten it to the low part of the stem at the

M10 threaded hole interface, a minimal amount of 6 turns of engagement should be

respected in order to engage enough threads to withstand the braking forces!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scott Plasma 5 - 2015 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scott Plasma 5 - 2015

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info