664134
7
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
ENGLISHENGLISH
FORK
Setup screw:
front end height can be set to adjust the front wheel tire clearance with the frame
thanks to the fork dropout screws M5 (511). The fork (200) length can be set from
370mm to 380mm.
- Loosen the screws to set a higher front end
- Tighten the screws to set a lower front end.
Make sure right and left side are set at the same length by assembling the front
wheel and verifying it is centred with the fork crown.
Drop out adjustment screws: Standard M5*10mm headless screw available in any
hardware shop.
IMPORTANT
Make sure the inner diameter bearing chamfer is positioned onto the fork bearing
seat cone, place the stem (301A/B) into the frame headtube cut-out, place the fork
(201) into the headtube, push the fork (201) from below so that the steerer tube goes
through the stem 1” hole.
Put the upper 1” bearing (902) into the headtube upper bearing seat on top of the
headtube
IMPORTANT
Put the upper 1” bearing (902) into the headtube upper bearing seat on top of the
headtube, make sure the outer diameter bearing chamfer is positioned upon the
headtube bearing seat chamfer.
IMPORTANT
Put the 1” compression ring (903) on the steerer tube, make sure the compression
ring chamfer is positioned onto the 1” upper bearing inner diameter chamfer (face
down), put the top cap (904) on the top of the headset and tighten the M6 screw
(907) to the specified torque (T17), place the two M5 screws (303) into the recesses
located at the rear end of the stem body (301A/B), slide the stem on the steerer tube
to achieve its correct positioning, and make sure it does not touch the frame at any
point, tighten up the screws (907) to the specified torques (T1).
Once the cable routing is done, place the headtube cap (905) on the top of the
headtube and tighten the M4 screw (906) to the specified torque (T18).
Headset compression kit SCOTT part number: 239282
Headset Syncros Drop-In 1” - 1 1/8SCOTT part number: 238601
HEADSET/STEM BODY TT5
Headset/Stem body assembly:
put the compression kit (908) into the steerer tube and tighten the bolt to the
specified torque (T16) , position the lower 11/8 bearing (901) onto the fork (201)
bearing seat
13 |
BIKE USER MANUAL | PLASMA 5PLASMA 5 | BIKE USER MANUAL
| 12
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scott Plasma 5 - 2017 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Scott Plasma 5 - 2017

Scott Plasma 5 - 2017 Bedienungsanleitung - Deutsch - 13 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info