Bedienungsanleitung Seagate Barracuda 7200.11 Serial ATA (Seite 20 von 50) (Englisch)

676459

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

14 Barracuda 7200.11 Serial ATA Product Manual, Rev. E

2.7.2 Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on

the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.

• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write

current.

2.7.3 Voltage tolerance

Voltage tolerance (including noise):

5V +10% / -7.5%

12V +10% / -7.5%

2.7.4 Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems,

you can control power management through the system setup program. The drive features the following

power-management modes:

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc

access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set

the standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for

a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In

Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive

accepts all commands and returns to Active mode any time disc access is necessary.

•Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buf-

fer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it

receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and

enters Standby mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and

begins counting down from its specified delay times to zero. If the standby timer reaches zero before any

drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the

drive accepts all commands and returns to Active mode when disc access is necessary.

Power modes Heads Spindle Buffer

Active Tracking Rotating Enabled

Idle Tracking Rotating Enabled

Standby Parked Stopped Enabled

Sleep Parked Stopped Disabled

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seagate Barracuda 7200.11 Serial ATA Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info