Bedienungsanleitung Seat Alhambra 2010 (Seite 342 von 382) (Englisch)

817399

342

Zoom out

Zoom in

Vorherige Seite

1/382

Nächste Seite

If and when340

The vehicles should not touch. Otherwise, current may be allowed to flow

when the positive poles are connected.

Connect the clamps so they have good metal-to-metal contact with the termi-

nals.

If the engine fails to start straight-away, switch off the starter after about 10

seconds and try again after about a minute.

Complete operations only in the sequence given.

Jump lead terminal connections

xSwitch off the ignition of both vehicles page 175.

xLikewise, open the battery cover in the engine compartment page 289,

or remove the positive pole cap from one side 3), in the direction of the arrow

page 339, fig. 212.

xConnect one end of the red jump lead to the positive terminal

page 339, fig. 213 or page 339, fig. 212 of the vehicle with the

flat battery .

xConnect the other end of the red jump lead to the positive terminal in

the vehicle providing assistance .

xFor vehicles without Start-Stop system: Connect one end of the black

jump lead to the negative terminal in the vehicle providing assistance

page 339, fig. 213.

xFor vehicles with Start-Stop system: Connect one end of the black

jump lead to a suitable ground connection, a solid piece of metal in the

engine block, or to the engine block page 339, fig. 214.

xConnect the other end of the black jump lead to a solid metal compo-

nent connected to the engine block, or onto the engine block itself of the

vehicle with the flat battery however, connect it as far away as possible from

the battery .

xPlace the leads so that they cannot be caught by any moving parts in the

engine compartment.

Switching on

xStart the engine of the vehicle supplying current and let it run at idling

speed.

xStart the engine of the car with the flat battery and wait two or three

minutes until the engine is “running smoothly”.

Removing the jump leads

xBefore you remove the jump leads, switch off the headlights (if they are

switched on).

xTurn on the heating and rear window heater in the vehicle with the flat

battery. This helps minimise voltage peaks which are generated when the

leads are disconnected.

xWith the engines running, disconnect the leads in reverse order to

connection.

xClose the battery cover, or replace the positive pole cap 3).

WARNING

Incorrectly jump starting could cause the battery to explode resulting in

serious injury. Please observe the following rules to minimise the risk of a

battery explosion:

xAll work involving the vehicle battery and electrical system can cause

corrosion, fire and serious electric shocks. Always read and take into

account the safety warnings and standards before beginning work on the

battery page 289, “Vehicle battery”.

xAlways protect your eyes with suitable working goggles and never lean

over the vehicle battery.

xThe jump leads must be connected in the correct order: first the positive

cable, then the negative cable.

xDo not attach the negative cable to parts of the fuel system or to the

brake hose/pipe.

3) Vehicles whose battery is not located in the engine compartment page 339.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seat Alhambra 2010 Seite 342

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seat Alhambra 2010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info