Bedienungsanleitung Seat Ateca 2022 (Seite 52 von 371) (Englisch)

817351

Zoom out

Zoom in

Vorherige Seite

1/371

Nächste Seite

Emergencies

Raising and lowering windscreen wiper

arms

●Place the windscreen wipers in the service

position ››› page 49.

●Grip the wiper arms only by the blade's

fastening point.

Cleaning windscreen wiper blades

●Raise the wiper arms.

●Use a soft cloth to remove dust and dirt

from the windscreen wiper blades.

●If the blades are very dirty, a sponge or

damp cloth may be used ››› .

Changing the windscreen wiper blades

●Lift and unfold the wiper arms.

●Press and hold release button ››› Fig. 41 1

and pull gently on the wiper blade in the di-

rection of the arrow.

●Fit a new wiper blade of the same length

and design on to the wiper arm and hook it

into place.

●Rest the wiper arms back onto the wind-

screen.

Changing the rear window wiper blade

●Lift and fold the wiper arm.

●Turn the blade slightly ››› Fig. 42 (arrow A).

●Hold down the release button 1 while gen-

tly pulling the blade in the direction of arrow

●Insert a new blade of the same length and

type in the rear wiper arm in the opposite di-

rection to the arrow B and hook into place

button 1.

●Replace the wiper arm on the rear window.

WARNING

Worn or dirty windscreen wiper blades re-

duce visibility and increase the risk of acci-

dent and serious injury.

●Always replace damaged or worn wind-

screen wiper blades or blades that no lon-

ger clean the windscreen properly.

CAUTION

●Damaged or dirty windscreen wipers

could scratch the glass.

●If products containing solvents, rough

sponges or sharp objects are used to clean

the blades, the graphite layer will be dam-

aged.

●Never use fuel, nail varnish remover, paint

thinner or similar products to clean the win-

dows.

●In icy conditions, always check that the

wiper blades are not frozen to the glass be-

fore using the wipers. In cold weather, it

may help to leave the vehicle parked with

the wipers in service position ››› page 49.

CAUTION

●To prevent damage to the bonnet and the

wiper arms, only leave them in the service

position.

●Before driving, always lower the wiper

arms.

Jump start

Jump leads

The jump lead must have a sufficient wire

cross section.

If the engine fails to start because of a dis-

charged battery, the battery can be connec-

ted to the battery of another vehicle to start

the engine.

Jump leads must comply with standard DIN

72553 (see cable manufacturer's instruc-

tions). The wire cross section must be at least

25 mm2 for petrol engines and at least

35 mm2 for diesel engines.

Note

●The vehicles must not touch each other,

otherwise electricity could flow as soon as

the positive terminals are connected.

●The discharged battery must be properly

connected to the on-board network.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seat Ateca 2022 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seat Ateca 2022

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info