Bedienungsanleitung Seat Exeo ST 2013 (Seite 299 von 327) (Englisch)

817454

299

Zoom out

Zoom in

Vorherige Seite

1/327

Nächste Seite

297If and when

–Connect one end of the red jump lead to the positive + termi-

nal of the vehicle with the flat battery A ⇒ Fig. 246.

–Connect the other end of the red jump lead to the positive ter-

minal + in the vehicle providing assistance B.

–Connect one end of the black jump lead X to a suitable ground

terminal, a solid piece of metal in the engine block, or to the en-

gine block ⇒ Fig. 246.

–Connect the other end of the black jump lead X to a solid met-

al component bolted to the engine block or to the engine block

itself of the vehicle with the flat battery. However, connect it to

a point as far as possible from the battery A.

4. Position the leads in such a way that they cannot come into

contact with any moving parts in the engine compartment.

Starting

5. Start the engine of the vehicle with the boosting battery and let

it run at idling speed.

6. Start the engine of the vehicle with the flat battery and wait two

or three minutes until the engine is “running”.

Removing the jump leads

7. Before you remove the jump leads, switch off the dipped beam

headlights (if they are switched on).

8. Turn on the heater blower and heated rear window in the vehi-

cle with the flat battery. This helps minimise voltage peaks

which are generated when the leads are disconnected.

9. When the engine is running, disconnect the leads in reverse or-

der to the details given above.

Connect the battery clamps so they have good metal-to-metal contact with

the battery terminals.

If the engine fails to start, switch off the starter after about 10 seconds and

try again after about half a minute.

WARNING

●Please note the safety warnings referring to working in the engine

compartment ⇒ page 235.

●The battery providing assistance must have the same voltage as the

flat battery (12V) and approximately the same capacity (see imprint on

battery). Failure to comply could result in an explosion.

●Never use jump leads when one of the batteries is frozen. Danger of

explosion! Even after the battery has thawed, battery acid could leak and

cause chemical burns. If a battery freezes, it should be replaced.

●Keep sparks, flames and lighted cigarettes away from batteries, dan-

ger of explosion. Failure to comply could result in an explosion.

●Observe the instructions provided by the manufacturer of the jump

leads.

●Do not connect the negative cable from the other vehicle directly to

the negative terminal of the flat battery. The gas emitted from the battery

could be ignited by sparks. Danger of explosion.

●Do not attach the negative cable from the other vehicle to parts of the

fuel system or to the brake line.

●The non-insulated parts of the battery clamps must not be allowed to

touch. The jump lead attached to the positive battery terminal must not

touch metal parts of the vehicle, this can cause a short circuit.

●Position the leads in such a way that they cannot come into contact

with any moving parts in the engine compartment.

●Do not lean on the batteries. This could result in chemical burns. 

Safety First Operating instructions Practical Tips Technical Specifications

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seat Exeo ST 2013 Seite 299

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seat Exeo ST 2013

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info