Bedienungsanleitung Sebo D2 TOTAL ECO (Seite 13 von 15) (Englisch)

671278

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

CLOG REMOVAL

OTE! D4 users with ET-1 or ET-2 power heads, please refer to your power head

user’s manual for more detailed instructions for removing clogs in your power head.

If the “bag full or clog” warning indicator (12) remains orange after the filter bag has

een changed and the filters are in good condition, there is likely a clog in the sys-

tem.

Clogs in the Head or Brush - Figure 32

Clogs in the swivel neck (57) of a head or brush can be cleared by first pressing the tool

release button (9) and removing the brush or head. Check inside the swivel neck chan-

nel (58), and clean out pathway.

Clogs in the Telescopic Tube - Figure 33

Remove head from telescopic tube (5) by pushing the tool release button (9) and pulling

the tube out. Remove the handle grip (1) from the top of the telescopic tube by pushing

the tube release button (3). A stiff wire or stick can be used to push the clog out of the

tube.

Clogs in the Hose - Figures 33, 34, 35 & 36

Check for suction at the end of the hose by removing the handle grip (1) from the tele-

scopic tube (5) and putting your hand over the handle grip suction opening (59). Turn

the power on and slide the suction up to full power. If you feel reduced suction, the

blockage is in the hose.

If the blockage is in the hose, there are two ways to clear it:

1. With the telescopic tube disconnected from the handle grip (1), hold the hose upright

with one hand blocking the handle grip suction opening (59) and switch on the machine

with full suction power. If necessary, quickly lift your hand on and off the end of the

hose. If that does not clear the clog, you may also clear clogs by reversing the hose -

see #2 below.

2. With the power off, remove the hose neck (#14, figure 34) from the suction opening

(19) by squeezing the two release buttons (13). Remove the handle grip (1) from the tel-

escopic tube (figure 35) and insert the handle end of the hose (1) into the suction open-

ing (figure 36). Note: the handle will not fit snugly into the suction opening. Then, hold

the hose upright with one hand blocking the hose neck end and switch on the machine

at full suction power. If necessary, quickly lift your hand on and off the neck end of the

hose (figure 36). After the clog is removed, replace the hose in the correct position.

Note! Do not insert a wire or stick into the hose. Doing so may cause damage to the

hose.

Clogs in Entrance to Filter Bag - Figure 37

Remove hose neck (14) from vacuum cleaner (see figure 34), open

the filter bag cover (see page 11) and clean out entrance to bag (60).

Figure 34

Always switch off power and unplug vacuum from outlet

before removing any clogs!

Figure 32

Figure 36

Figure 33

Figure 35

Figure 37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sebo D2 TOTAL ECO Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info