804503

Segway Ninebot Gokart Kit Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
Scan the QR code below Download in Google Play Store
or Apple's App Store
Remove the steering bar from the miniPRO Assembling and disassembling the Gokart This assembly is for adults only. Do not power on the miniPRO during assembly or disassembly.
Assembly
Check the status of the miniPRO
Operating the miniPRO
Activate the Gokart Use and charging
* Your mobile phone requires Bluetooth 4.0 or later, iOS system 8.0
or later, or Android™ 4.3 or later.
For your safety, the default values of the Gokart speed and
sensitivity are set to low. Use the app to learn how to drive
safely, then the speed limit can be gradually raised.
Follow the relevant charging instructions in the manual and the common battery maintenance and safety knowledge for
maintenance. Ninebot products are designed with overheat protection. If the vehicle temperature exceeds 104 °F (40°C),
the vehicle cannot be charged as normal. Wait until the vehicle cools to below 104 °F (40°C) before charging.
Specifications
6
4
Assembling your Gokart (Requires two adults to assemble)
Update the miniPRO firmware
1
2
3
Located under the frame. Remove
the attachment strap before
removing from the frame.
The installation direction is as shown below.
Be sure to align the steel frame with the
adapter pad as shown in the enlarged view.
5
Driving the Gokart
Install the app
Download the Segway-Ninebot app (hereinafter referred to as the app)
by any of the following methods:
Refer to the chapter “Maintenance” in the miniPRO User Manual to ensure that the tire
performance, the battery level, and the running status of the miniPRO are normal.
Turn on the phone's Bluetooth.
Press the power button to turn
on the miniPRO.
Open the app to search for and
connect your miniPRO.
e. Use the tools provided to remove the steering bar bracket from the miniPRO.
The steps are as follows:
Segway-Ninebot App
Pair your mobile phone and the miniPRO
Segway-Ninebot App
Disassembly
In the upper right corner of the app, tap Settings Firmware Update.
On the Ninebot settings page, tap "Gokart mode".
Enable "Gokart mode".
Update firmware and switch modes
Searching
Gokart0001
Gokart Mode
Gokart Mode
Gokart Kit installation tutorial
About Gokart
Vehicle
Vehicle
Firmware
Update
Gokart
Mode
Press the power button on the miniPRO to turn on the Gokart.
The Gokart will automatically power off when idle for 10 minutes.
Open the Segway-Ninebot APP and connect your Gokart.
Follow the instructions in the app to activate the Gokart
and complete the corresponding tutorial and exercises.
Place the steering
bar bracket
removal tool into
the screw holes on
the steering bar
bracket.
Fasten the two metal molds onto
the lower part of the steering bar
bracket by inserting the two nuts
from the right and the two M5
screws from the left; tighten with
a 4mm hex wrench.
Insert the M6 screw into the
screw hole on the front of
metal molds, tightening with
a 5mm hex wrench, continue
tightening the screw until the
steering bar bracket falls off
the miniPRO.
If lifting the frame by yourself, do not lift the
backside more than 19° or you may
damage the bumper.
Install the miniPRO adapter pad.
2
Plug the power extension cord into the charging port of the miniPRO,
tighten by turning clockwise.
1
Once fully assembled, make sure:
9
Place the Gokart frame on the miniPRO.
3
3
2
2
3
3
6
4
4
5
5
1
6
Pass the attachment straps through
the bottom of the miniPRO and the
strap fixing holes. Tighten the straps.
4Plug the electrical connection
cable of the Gokart into the
power extension cord. Align
the groove and do not force
the cord in.
5
Stretch the frame and adjust the length of the body:
6
Adjust the steering wheel height:
7
Install the Gokart batteries.
8
Power
button
Power
button
Please make sure the location of the logo
is correct on the straps. If not, return to
step for adjustment. Charge ports must be dry.
Press the miniPRO's power button
to turn off the Gokart.
Disconnect the electrical connection
cable.
Refer to the assembly procedure and
carry it out in reverse order.
a With both hands holding the steering wheel and the seat,
stretch the frame out to a suitable position along the
horizontal direction of the connection tube.
b Align the scalable structure of the frame with the
marking on the connection tube.
c Positioning: Use a 5mm hex wrench to press the two
screws into the holes on the left and right connection
tube in order, as shown in the figure above (The screw is
set to a depth of about 1cm for successful position).
d Tighten the 4 screws.
a Raise the steering wheel to a
suitable height.
b Insert the quick release
screw into the hole of the
corresponding height.
c Tighten the quick release nut.
d Press to fix the steering wheel
quick release components.
e Ensure the steering wheel does
not shake. Otherwise, repeat
the steps b, c, d, e.
Unscrew the battery
compartment cover and
insert batteries into the
compartment. Close and
tighten the cover.
To avoid issues that may be
caused by corrosion,
remove the batteries if not
using the Gokart for an
extended period of time.
The miniPRO adapter pad and the mini-
PRO are facing the correct direction.
The attachment straps are properly at-
tached and tightened.
The electrical connection cable is
plugged into the power extension cord.
The body length and steering wheel
height is appropriate for the rider.
The battery compartment is closed.
If anything appears to be incorrect,
stop using the Gokart and
contact after-sales
service.
< 19°
Acceleration: lightly press the throttle (right
pedal) to go forward.
Deceleration: lightly press the brake (left
pedal) to decelerate.
Steering: steer the Gokart by slightly turning the
steering wheel clockwise or counterclockwise.
Do not pump the brake pedal to decelerate.
Driving
1
Sitting on the seat, buckle the left and
right parts of the seat belt in front of you.
Fastening the seat belt
When the Gokart is stopped, double-press
the brake (left pedal). After you hear a beep,
the Gokart has switched to reverse mode.
Press the throttle to drive the Gokart in
reverse. Double-press the brake (left pedal)
again to return to forward mode.
Reversing
In the event of a situation that requires an
emergency stop, pull the hand brake handle on
the right side of the Gokart to engage the
emergency brake.
Emergency braking
Make sure the vehicle is completely stopped
before getting off. Press the miniPRO's power
button to turn off the Gokart.
Shutdown
Charge the Gokart by plugging the miniPRO
power cord into the power extension cord.
Do not connect the charger if the charge
port or power cable is wet.
Charging
Product
Supported
models Name and model
Size
Weight
Driving
Machine
Parameters
Tires
Light
Brake
Front
compartment
battery[3]
Name Ninebot Gokart Kit
N4MZ98
43.1×34.1×20.1 in (1095×865×510 mm)
Ninebot by Segway miniPRO (Model: N3M260, N3M320)
NinebotS (Model:N3M240)
After extension (Max status): 54×32×24 in (1383×822×600 mm); before extension
(Min status): 40×32×18 in (1004×822×459 mm)
Model
Vehicle size
Package size
Max payload 220 lbs (100 kg)
61.3 lbs (27.8 kg)
51-75 in (130-190 cm)
14+ years old
15 mph (24 km/h)
5 mph (8 km/h)
2 mph (3 km/h)
9 mile (15km)
2.1:1
1.6 in (40 mm)
15°
14°F~ 104°F (-10～40℃)
-4°F~ 122°F (-20～50℃)
IPX4
6 AA Batteries
20 ft (6 m)
Tire width: 3 in (80 mm); flatness ratio: 60%; hub diameter: 5 in (127 mm)
Non-inflatable hollow tire
0.2 Watt white LED light bar
Electronic brake + mechanical handbrake
Hardened road, flat road surface, slopes below 15°
The indicator comes in three colors: blue, yellow, and red. Blue means that the vehicle is in normal
condition. Yellow means that the vehicle needs to be activated or the batteries in the front compartment
need to bereplaced. Red means that the vehicle has a performance failure, and you need to open the
app to check the cause of the failure and contact the after-sales service.
Net weight
Height requirement
Recommended Age
Speed limit
Novice speed limit
Reversing speed limit
Steering ratio
Ground clearance
Traversable Terrain
Operating temperature
Storage temperature
IP rating
Model/Quantity
Front tires
Type
Headlight
Status indicator
Braking method
Braking distance[4]
Maximum slope [2]
Typical Range[1]
Power extension
cord
Four screws
already inserted
into the screw
holes.
Do not plug the power
extension cord into the
miniPRO if the power
extension cord or charge
port is wet.
Searching
MiniPro0001
a
b
b
b
c
d
cd
a
Activate the
Gokart
a. Press the power button
to turn off the miniPRO.
b. Unlock the steering bar
tool-free release, remove
the steering bar.
c. Remove the rubber plug on
the steering bar bracket.
d. Use a 4 mm hex wrench
to remove the screws in
the steering bar bracket
and pull off the bracket.
Disassembly is completed
after removing the steering
bar bracket. If you cannot
remove the bracket by
hand, continue to step e.
The Gokart is assembled by attaching the Gokart Kit to a miniPRO.
Before assembly of the Gokart, please review the miniPRO User Manual
and follow all instructions contained in it. Once the miniPRO has been
properly activated and charged you can begin assembly of the Gokart.
* This firmware update does not involve activation of the miniPRO. If you need to use the miniPRO,
please refer to the miniPRO User Manual for related operations.
Before assembly, update the app's firmware and turn
on Gokart mode.
[1] Typical Range : Under the
circumstances of full power, 154
lbs (70kg) load, and 77°F(25℃)
ambient temperature, and
measured on a flat road at an
average speed of 9 mph (15
km/h).
[2] Maximum slope: Refers to the
maximum slope that a 220 lbs
(100 kg) driver can climb at a
speed not faster than 3 mph (5
km/h).
[3] Front compartment battery:
The battery compartment inside
the frame that is used to power
the frame indicator/headlight.
When the battery is low, the blue
indicator light turns yellow and
blinks. You need to replace the
batteries yourself.
[4] Braking distance: Under the
circumstances of full power, 154
lbs (70kg) load, and measured on
a flat hard road at an average
speed of 12.4 mph (20 km/h).
Note: You can also open the App
for more specific tips.
miniPRO Assembly
Instructions
Scan the QR code on the
right to review Assembly
Instructions.
This manual uses the miniPRO as an example. If you have a Ninebot S, please watch the
video by scanning the right QR code.
Ninebot S Assembly
Instructions
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Segway Ninebot Gokart Kit wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info