Bedienungsanleitung Seiko DH33 (Seite 10 von 15) (Englisch)

757456

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

English

DISPLAY AFTER A DIVE

Current depth

When you are less than 1.5 m (5 ft) underwater and

the auto switch senses water:

●The watch shows the dive display with the current depth being

“0.0 m (0 ft)”.

●If the watch shows the dive display after you surface, check

that water does not remain on the auto switch.

●If the watch measures the current depth of greater than 1.5 m

(5 ft) within 10 minutes after this display is shown, the

previous and the new dives are considered inseparable, and

the dive times of both dives and the surface interval time are

added together.

Indication DescriptionWarning

Ascent rate warning

(flashing)

WARNINGS DURING A DIVE

If you ascend in water at a rate greater than the specified one, flashing “SLOW”

appears for 5 seconds and the warning sound beeps for 3 seconds.

Three rates are specified depending on the depth level.

0.0 ~ 5.9 m (0 ~ 19 ft) : 8 m (26 ft)/min

6.0 ~ 17.9 m (20 ~ 59 ft) : 12 m (39 ft)/min

18.0 m (60 ft) and deeper : 16 m (52 ft)/min

* The watch calculates the ascent rate by measuring the current depth every 6 seconds.

Decompression

warning

Decompression stop

violation warning

(flashing)

If you accidentally exceed the no-decompression limit, the watch is shifted to the

decompression mode, flashing “DECO” is shown, and the warning sound beeps

for 3 seconds.

If you ascend to a depth shallower than the decompression stop depth that the

watch indicates, it gives a decompression stop violation warning. The current

depth, decompression stop depth, decompression stop time and “DECO” all

flash, and the warning sound beeps for 3 seconds.

When you return to a depth deeper than the decompression stop depth, the watch

starts counting down the decompression stop time.

PO2 limit warning

(Warning on partial

pressure of oxygen)

(flashing)

If the partial pressure of oxygen (PO2) reaches 1.5, the warning sound beeps for

3 seconds. By pressing and holding button C to show PO2, you can see some of

the oxygen limit indicators flashing.

If PO2 exceeds 1.6, the “O2” mark starts flashing, and the warning sound beeps

for 3 seconds. By pressing and holding button C to show PO2, you can see all the

oxygen limit indicators flashing.

OLI warning

(Warning on oxygen

limit)

It appears when all the oxygen limit indicators are flashing.

(flashing)

Out of range warning It appears when the measurement exceeds the specified value as follows:

• Maximum depth exceeds 99.9 m (328 ft).

• Dive time exceeds 599 minutes.

• Decompression stop depth exceeds 15 m (50 ft).

• Decompression stop time exceeds 99 minutes.

(flashing)

* The watch will not measure the current depth while the warning sound is beeping.

When you are less than 1.5m underwater or on the

surface and the auto switch does not sense water:

• TIME/CALENDAR display

Desaturation

time

Surface interval

time

Press and hold to show the surface interval time

and desaturation time.

English

HOW TO USE DIVE COMPUTER FUNCTIONS HOW TO USE DIVE COMPUTER FUNCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seiko DH33 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seiko DH33

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info