Bedienungsanleitung Sencor SCE3000BK (Seite 7 von 10) (Englisch)

688540

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Coffeemaker

SCE 3000BK

EN-7

OPERATING THE COFFEEMAKER

1) Fill the glass kettle 5 with the required amount of water. The water level must reach at least the

minimum water level mark 1/MIN (i.e. 1 cup of water) and must not go above the maximum water

level mark, i.e. 12 cups of water (1 cup = 125 ml). Open the lid 1 and pour the contents of the

kettle into the water tank 2.

Attention:

Only ﬁll the water tank with cold drinking water. Do not use hot water.

The water tank has a maximum capacity of 1.5 litres of water.

The amount of brewed coffee will always be less than the amount of water you poured into the

water tank. During the coffee brewing process, approximately 10% of the water is absorbed by

the ground coffee.

2) Place the permanent ﬁlter or a disposable paper ﬁlter size no. 4 into the ﬁlter holder 9.

3) Pour ground coffee into the ﬁlter. Recommended dosage: 7 g of ground coffee per cup.

4) Shut the lid 1 and make sure that it is properly closed.

5) If you wish to brew a stronger coffee, turn the aroma regulator 8 anticlockwise. For weaker

coffee, turn the regulator 8 in the opposite direction.

6) Place the glass kettle 5 on the hotplate 6 and start the coffeemaker by pressing the power switch 7.

The red indicator light will be lit.

7) Once the entire batch of coffee has ﬁnished brewing, wait approximately 1 minute for the drip

process to complete fully. Now the coffee can be served.

8) If you wish to serve the coffee later, leave the kettle on the hotplate. The hotplate will keep the coffee

at an optimal serving temperature for 40 minutes, then the coffeemaker will turn off automatically.

9) Once you have emptied the kettle, put it back on the hotplate and turn the coffeemaker off by

pressing the power switch. The red indicator light will turn off.

10) Allow the coffeemaker to cool down for at least 10 minutes before using it again.

Warning:

If you do not allow the coffeemaker to cool down, the water could overheat and result in

subsequent scalding by the escaping steam.

11) Before using the coffeemaker again, remove the coffee grounds and wash the permanent ﬁlter 0

or remove the paper ﬁlter together with the coffee grounds and dispose of it together with normal

household waste. Rinse the ﬁlter holder 9 and kettle 5 under running water. Dry it and put it

back in its place.

12) If you will not be using the coffeemaker, disconnect the power cord from the el. power socket.

DRIP-STOP FUNCTION

The Drip-Stop function will allow you to serve coffee before the end of the drip process.

1) Take the kettle out of the coffeemaker once approximately 4 cups of coffee have been brewed. The

Drip-Stop shut-off valve will be activated and coffee will stop dripping.

2) Serve the required amount of coffee and place the kettle back on the hotplate within 1 minute of

taking it out to avoid the ﬁlter from overﬁlling with hot water.

3) When the kettle is placed back on to the hotplate, the drip process will resume automatically.

Note:

Coffee served prior to the completion of the drip process may taste differently to the coffee

served at the end of the drip process.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SCE3000BK Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info