Bedienungsanleitung Sencor SFE 4021 (Seite 5 von 6) (Englisch)

759912

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

03/2017

- 5 -

EN Desktop Fan

User'smanual

■ Prior to using this appliance, please read the user’smanual

thoroughly, even in cases, when one has already familiarised

themselves with previous use of similar types of appliances. Only

use the appliance in the manner described in this user’smanual.

Keep this user’smanual in asafe place where it can be easily

retrieved for future use.

■ We recommend saving the original cardboard box, packaging

material, purchase receipt and responsibility statement of the

vendor or warranty card for at least the duration of the legal

liability for unsatisfactory performance or quality. In the event

of transportation, we recommend that you pack the appliance

in the original box from the manufacturer.

DESCRIPTION OF THE APPLIANCE

A1 Front protective grill

A2 Fan blade fastening nut

A3 Fan blades with adiameter of 30 cm (SFE 3011BK) /

40 cm (SFE 4021BK)

A4 Nut for fastening the rear protective grill

A5 Rear protective grill with fastening clamps and acarry handle

A6 Motor unit shaft

A7 Horizontal oscillation toggle switch

A8 Motor unit with adjustable vertical tilt angle

A9 Panel with control buttons

0 – o, 1 – low speed, 2 – medium speed, 3 – high speed

A10 Base

Note:

The accessories include ascrew and anut for joining the

protective grills.

BEFORE FIRST USE

■ Take the appliance and its accessories out of the packaging

materials. Before disposing of the packaging materials, make

sure that no part of the appliance is missing.

ASSEMBLING AND DISASSEMBLING THE APPLIANCE

■ Insert the control panel A9 from above into the base A10 and

make sure that it is properly seated inside. Grasp the fan under

the motor unit A8 and turn it upside down. Turn the wing nut

located underneath the control panel A9 by 90° to secure the

panel A9 to the base A10 (see g. B). Turn the fan back over to

the operating position and stand it on astraight, clean, dry, stable

and smooth surface.

■ Place the rear protective grill A5 against the front side of the

motor unit A8 so that the handle is above the motor unit A8

and that the alignment tabs on the front side of the motor unit

A8 slide into the respective holes in the rear grill A5. Place the

nut A4 on to the shaft A6 and screw it in clockwise to secure the

rear protective grill A5 to the motor unit A8. Before tightening

the nut A4, make sure that the rear grill A5 has not moved and

that the alignment tabs are still in the respective holes.

■ On to the shaft of the motor unit A6 put on the fan blades A3 so

that the shaft A6 properly slides into the centre part of the fan

blades A3. Push the fan blades A3 towards the motor unit A8 all

the way. Now, check that the fan blades A3 turn freely, and secure

them in place by screwing nut A2 anticlockwise on to the shaft

A6.

■ Release the clamps along the perimeter of the rear protective grill

A5. Place the front protective grill A1 against the rear protective

grill A5 so that the front grill A1 ts into the alignment hook in

the bottom part of the rear protective grill A5 and that the screw

holes at the top of both grills are aligned. Fasten the released

clamps along the perimeter of the grills. To ensure astrong

connection of the two grills, into the holes at the top of the grills

it is necessary to screw in the supplied screw and secure it with

the nut.

■ Before putting the fan into operation, check that it is correctly

assembled and that the protective grills are rmly joined.

■ To disassemble, proceed in reverse sequence.

OPERATING THE APPLIANCE

Setting the speed and turning o the fan

■ Locate the fan on an even, dry and smooth surface within reach

of apower socket. Connect the power cord to apower socket. To

set the air ow speed, use the buttons on the control panel A9.

The functions of the control buttons are described below:

0 – turn o the fan;

1– set alow air ow speed;

2 – set a medium air ow speed;

3– set ahigh air ow speed.

■ When you have nished using the fan, always turn it o and

disconnect it from the power socket.

Setting horizontal oscillation

■ The horizontal oscillation of the motor unit A8 can be set using

the toggle switch A7. To start the horizontal oscillation, push the

toggle switch A7 down. The motor unit A8 will oscillate from side

to side at an angle of approximately 90°.

■ To turn o the oscillation, pull the toggle switch A7 up. This will

turn o the oscillation.

Setting the vertical tilt angle of the motor unit

■ Before setting the vertical tilt angle of the motor unit A8, rst

turn o the fan. Set the desired angle of the motor unit A8 and

then you may start the fan again.

Note:

The motor unit A8 may only be tilted up and down in

alimited range. Do not set the tilt angle of the motor unit

A8 by force.

CLEANING AND MAINTENANCE

■ Before cleaning it, make sure that the appliance is turned o and

disconnected from the power socket.

■ Regularly remove dust from the appliance. For normal cleaning,

aclean, dry cloth is sufficient. In the event that it is dirtier,

disassemble the appliance and wipe the individual parts with

awiping cloth slightly dampened in asolution of warm water and

neutral detergent. Then wipe everything so that it is thoroughly

dry. Make sure that no water enters the motor unit A8 or into the

control panel A9 while cleaning.

■ Prior to reassembly, make sure that all parts of the appliance are

dry.

■ Do not submerge the appliance or its power cord in water and

do not wash it under running water.

■ For cleaning do not use steel wool, cleaning products with an

abrasive eect, petrol and other solvents.

STORAGE

■ If you will not be using the fan for an extended period of time,

store it in aclean, dry place or disassemble it and put it back into

the box.

Sencor SFE 4021 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sencor SFE 4021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info