Bedienungsanleitung Sencor SFN 5011WH (Seite 7 von 9) (Englisch)

759172

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

- 7 - 05/2020

EN Air Cooler

User'smanual

■ Prior to using this appliance, please read the user'smanual thoroughly, even in cases,

when one has already familiarised themselves with previous use of similar types of

appliances. Only use the appliance in the manner described in this user’smanual.

Keep this user'smanual in asafe place where it can be easily retrieved for future use.

■ We recommend saving the original cardboard box, packaging material, purchase

receipt and responsibility statement of the vendor or warranty card for at least the

duration of the legal liability for unsatisfactory performance or quality. In the event

of transportation, we recommend that you pack the appliance in the original box

from the manufacturer.

DESCRIPTION OF THE APPLIANCE

A1 Remote control signal receiver

A2 Control panel with display

A3 Horizontal flaps with manually

adjustable tilt

A4 Air outlets

A5 Vertical flaps

A6 Water level indicator with MIN and

MAX marks

A7 Integrated handle

A8 Storage space for the remote

control

A9 Washable dust filter

A10 Washable water filter

A11 Power cord

A12 3-litre removable water tank

A13 Water tank lock

A14 Travel wheels

A15 Remote control

A16 Cooling insert (2 pcs)

DESCRIPTION OF THE CONTROL PANEL

B1 On/Off button

B2 Fan speed setting button

B3 Cooling / humidification mode

button

B4 Operating mode selection button

B5 Automatic shut-off timer button

B6 Flap motion button

B7 Fan speed setting indicator lights

B8 Cooling / dehumidification mode

indicator light

B9 Operating mode indicator lights

B10 Timer indicator lights

B11 Flap motion indicator light

DESCRIPTION OF THE REMOTE CONTROL

C1 On/Off button

C2 Flap motion button

C3 Operating mode selection button

C4 Cooling / humidification mode

button

C5 Timer button

C6 Fan speed setting button

BEFORE FIRST USE

■ Before first use, take the appliance and its accessories out of the packaging material

and remove all promotional labels and stickers. Check that neither the appliance nor

any of its parts is damaged.

INSERTING AND REPLACING BATTERIES IN THE REMOTE

CONTROL

■ From the underside side of the remote control A15, slide out the battery

compartment and insert a3V CR2032 battery into it, see figure D. While inserting

the battery, maintain the correct polarity.

■ If the battery in the remote control A15 is flat, replace it with anew battery of the

same type.

■ If you decide not to use the remote control A15 for an extended period of time, we

recommend removing the battery. If the battery were to leak into the inner area of

the remote control A15, this could result in its damage.

Note:

Never put batteries in afire, short circuit them or damage them in any

way. Dispose of them ecologically at the end of their lifetime. Never throw

batteries out with communal waste.

OPERATING THE APPLIANCE

Installation

■ Locate the appliance on an even, dry and stable surface within reach of aproperly

grounded power socket.

■ To ensure sufficient air circulation, leave aclearance of at least 30 cm on all the sides

of the appliance.

■ Make sure that the appliance is properly assembled and connect it to a power

socket. The appliance will make a sound and switch to the stand-by mode. All

buttons except for the B1 button will be disabled.

Turning the appliance on / off

■ Press the B1 button to start the appliance. The appliance will beep and start

running in the default setting.

Default settings:

1) Fan mode set to the lowest speed. (When the appliance is started for the first

time, it will first run at medium speed for approximately 3 seconds and then

automatically switch to the low speed. If you turn on the appliance from stand-by

mode, it will again start at medium fan speed for approximately 3 seconds and then

automatically switch to the low speed, if this speed was set before it was turned off.)

2) Cooling mode is turned off.

3) Operating mode: NORMAL and the indicator light is lit.

4 The timer is turned off.

5) Vertical flap motion is turned off.

■ To turn off the appliance, press button B1 . The appliance will make asound

and switch to the stand-by mode. When the appliance is turned off to the stand-by

mode, the previous settings are stored in memory. This does not, however, apply

when the appliance is disconnected from the power socket.

■ Always turn off the appliance and disconnect it from the power socket when you

have finished using it.

Setting the fan speed

■ Button B2 serves to set the fan speed. Press button B2 and select the

desired fan speed in the following order: (low speed) - (medium speed) -

(high speed). Each time it is pressed, the respective indicator light will be lit.

Setting the cooling / humidification mode

■ Button B3 is used to turn the cooling/humidification mode on and off. Indicator

light B8 is lit to indicate that the mode is activated. The pump will start running.

■ Before starting this mode, check that the water in the water tank A12 is at least

at the minimum mark. To fill the water tank with water, proceed according to the

instructions contained in section "FILLING THE WATER TANK".

Note:

To prevent the pump from becoming damaged due to long term use, the

pump will automatically turn off after 10 hours of continuous operation in

the cooling / humidification mode.

Setting the automatic shut-off timer:

■ Button B5 serves to turn on the timer. Repeatedly press button B5 to

change the timer in the following order: 1H – 2H – 4H – 8H – off. Each time it is

pressed, the respective indicator light will be lit. If "off" is selected, no indicator light

will be lit. The automatic shut-off timer durations cannot be accumulated. When the

selected time elapses, the appliance will automatically switch to the stand-by mode.

Setting an operating mode

■ Button B4 serves to set the operating mode. Repeatedly press button B4

to select the operating mode in the following order: (NORMAL = normal mode)

- (NATURAL = natural breeze) - (SLEEP = sleep mode). Each time it is pressed,

the respective indicator light will be lit.

■ In the NORMAL operating mode, the fan speed is constant.

■ In the NATURAL operating mode, the air flow speed is controlled automatically

based on the selected flow speed. This achieves the natural breeze effect.

Progression of the mode when high fan speed is set

High speed

Medium

speed

Low speed

Fan stops

Progression of the mode when medium fan speed is set

High speed

Medium

speed

Low speed

Fan stops

Progression of the mode when low fan speed is set

High speed

Medium

speed

Low speed

Fan stops

Sencor SFN 5011WH Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info