Bedienungsanleitung Sencor SMG 4200 (Seite 7 von 8) (Englisch)

758400

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

- 7 - 06/2020

EN Meat grinder

User’manual

■ Prior to using this appliance, please read the user‘smanual thoroughly, even in cases,

when one has already familiarised themselves with previous use of similar types of

appliances. Only use the appliance in the manner described in this user‘smanual.

Keep this user‘smanual in asafe place where it can be easily retrieved for future use.

In the event that you hand this appliance over to somebody else, make sure to also

include this user‘smanual.

■ Carefully unpack the appliance and take care not to throw away any part of

the packaging before you find all its parts. We recommend saving the original

cardboard box, packaging material, purchase receipt and responsibility statement

of the vendor or warranty card for at least the duration of the legal liability

for unsatisfactory performance or quality. In the event of transportation, we

recommend that you pack the appliance in the original box from the manufacturer.

DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES

A1 Motor unit base

A2 Main power switch

A3 Hole with shaft for attaching the

grinding chamber

A4 Grinding chamber

A5 Feed tube

A6 Safety clutch

A7 Gasket ring

A8 Screw shaft

A9 Cross blade

A10 Grinding disc

A11 Screw ring

A12 Filling tray

A13 Pusher

D1 Fruit juice draining groove

PURPOSE OF USE

■ The grinder is intended for processing meat, poultry, fish, fruits and vegetables.

■ The grinder is not intended for crushing bones, nuts or other hard ingredients or

frozen food.

BEFORE FIRST USE

■ Before using it, wash all parts that come into contact with food in hot water using

asmall amount of kitchen detergent, then rinse with clean water and wipe dry.

■ Wipe the outer surface of the motor unit base using asoft sponge dipped in warm

water with asmall amount of kitchen detergent and wipe it dry.

Attention:

When cleaning the cross blade A8, be very careful not to injure

yourself on its sharp cutting edges.

ASSEMBLY AND DISASSEMBLY OF THE GRINDING

ATTACHMENT

■ Prior to using this appliance, it is always necessary to correctly assemble the grinding

attachment (fig. B), which consists of parts A4 to A11.

■ Slide the gasket ring A7 on to the screw shaft A8, then insert the safety clutch A6

together with the shaft into the grinding chamber A4 with the safety clutch going

in first.

■ Put the cross blade A9 on to the end of the screw shaft. The cutting edge must point

outwards from the grinding chamber.

Attention:

When attaching the cross blade, be very careful not to injure

yourself on its sharp cutting edges.

■ Put the grinding disc A10 on to the blade. When putting on the disc, ensure that the

tab on the head of the grinding chamber slides into the grove on the grinding disc.

■ Screw the screw ring A11 on to the grinding chamber and tighten it firmly.

■ Put the assembled grinding attachment on to the motor shaft in hole A3 so that the

cogs on the rear part of the grinding attachment slide into the cogs on the motor

shaft (fig. C) and then turn the attachment anticlockwise. Check that the attachment

is properly attached and not moving in the motor shaft.

■ Put the filling tray A12 on to the feed tube A5 of the grinding chamber.

■ Now the grinder is assembled and ready for grinding food.

■ When disassembling, proceed in reverse sequence to the assembly.

GRINDING

■ Before grinding, remove any bones, cartilage and tendons from the meat. Cut the

meat into pieces measuring approximately 20 × 20 × 40 mm.

■ Cut fruit and vegetables into pieces that will freely pass through the feed tube.

Attention:

Never attempt to grind frozen meat or other types of frozen food.

It is necessary to allow frozen food to defrost completely before

grinding it.

■ Underneath the grinding attachment, place an appropriate bowl into which the

ground food will fall.

■ Place the appliance on an even, dry surface, unwind the power cord from the

underside of the motor unit base A1 and plug it into apower socket.

■ Place the food that you wish to grind on to the filling tray A12.

■ Turn on the grinder by pressing button A2.

■ Gradually place the food into the feed tube A5, and using the pusher A13, push

it down into the grinding chamber. To prevent the grinder from clogging, do not

overfill the feed tube. Push down gently on the pusher.

Attention:

Never use your fingers or other items to push food through the

feed tube while the grinder is running. Only use the supplied

pusher for this purpose.

■ To process food with a high juice content (certain types of fruit), the grinding

chamber A4 is equipped with agroove D1 for draining away excess juice.

■ In the event that the feed tube becomes clogged, first turn off the grinder using

button A2 and then disconnect it from the power socket. Then remove the

grinding attachment and clean away any processed food. If necessary, completely

disassemble the grinding attachment, clean it out and reassemble it. Put the

attachment back on to the motor unit base A1 and continue working.

Attention:

The maximum continuous operating time of the appliance

is 15 minutes. Then allow it to cool down for approximately

10minutes.

■ When you have finished using the grinder, turn it off using button A2 and disconnect

the power cord from the power socket. Ensure that the rotating parts have stopped

rotating and take the grinding attachment off the motor unit base A1, and then

disassemble it into its individual parts. Then clean all used parts according to the

instructions in chapter Cleaning and maintenance.

FUNCTION OF THE SAFETY CLUTCH

■ In the event that apiece of hard food enters the grinding chamber A4 and the screw

shaft A8 is subsequently jammed, the safety clutch A6 will break. In this way, the

motor unit is protected against overloading and damage.

■ In the event that the safety clutch breaks, always immediately stop working with the

grinder, turn it off and disconnect it from the power grid. Disassemble the grinding

attachment and thoroughly clean all its parts. Fragments of the broken clutch that

are not removed may again cause the screw shaft to jam or damage the motor unit.

After cleaning out the grinding attachment, slide anew safety clutch on to the screw

shaft and continue working.

Attention:

Never use the grinding attachment without the safety clutch A6.

This could lead to serious damage of the motor unit.

Sencor SMG 4200 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info