■Gently pull the gasket A9 around the entire perimeter to remove it from the holder A13. Carefully wash the gasket in warm water with asmall
amount of kitchen detergent. Rinse with clean water and wipe thoroughly until dry. In reverse sequence, carefully insert the gasket back behind
the holder.
■If the gasket is worn out or damaged, replace it with anew gasket of the same type.
PRESSURE CONTROL VALVE
■Carefully pull the pressure valve cover A12 from the underside of the lid, see fig. D. In the event that the cover cannot be removed by hand, use
asuitable flat screwdriver and carefully release the cover. Wash the cover in hot water with detergent, rinse it and dry it thoroughly.
■
Using adamp cloth or soft brush, clean the inner part of the pressure valve D1 and dry it with adry wiping cloth. Push the cover back on to the valve.
■Carefully pull out the steam release valve A7 from the outer side of the lid. Wash the valve, rinse and dry thoroughly.
■
Using adamp cloth or soft brush, clean the outer part of the pressure valve D2 and dry it with adry wiping cloth. Push the cover back on to the valve.
SAFETY FLOAT VALVE
■Carefully remove the cover E1 of the safety float valve A11 from the inner side of the lid. Remove the valve from the hole in the lid. Wash the
cover and the valve in hot water with detergent, rinse them and dry them thoroughly.
■Insert the valve into the hole in the lid and from the underside of the lid, slide the cover on to the valve.
Attention:
Never use the pressure cooker without the safety float valve cover or with adamaged cover.
Attention:
Before connecting the power cord into apower socket and into the pressure cooker and before turning the pressure cooker on
again, allow all surfaces to cool down completely.
TROUBLESHOOTING
PROBLEMPOSSIBLE CAUSEREMEDY
The pressure cooker cannot be
turned on.The power is not connectedCheck the connection of the power cord, plug and
the power socket.
The lid cannot be closed.The lid gasket is not seated correctly.Check the position of the gasket.
The lid cannot be opened.There is still pressure inside the pressure cooker.
Release the pressure from the pressure cooker by
turning the steam release valve to the release position
or release the steam manually using button A2.
The lid cannot be opened after the
steam has been fully released.The safety float valve is still in the hole in the lid.Using asuitable tool (e.g. skewer) push the valve into
the down position.
Alarge amount of steam is escaping
around the edge of the pressure
cooker.
The lid is not properly closed.Check the correct installation of the gasket in the lid.
The lid gasket is not in its place or is soiled by food
remains.Position the gasket correctly on the lid or clean it.
The lid gasket is worn out or damaged.Replace the damaged gasket with anew one of the
same type.
The lid is damaged or deformed (e.g. by falling on
the floor).Contact the service department.
Large amount of steam is escaping
from the safety float valve.
There are food remains on the lid gasket.Remove the gasket from the lid and clean it.
The lid gasket is worn out or damaged.Replace the damaged gasket with anew one of the
same type.
Steam is continuously escaping
through the steam release valve
even when it is in the cooking
position.
Valve fault.Contact the service department.
The hotplate is not heating.
The lid is not properly closed.Close the lid in the proper manner.
The hotplate is faulty or the power circuit is
defective.Contact the service department.
Code E1 is flashing on the display.Faulty bottom sensor.
Contact the service department.
Code E5 is flashing on the display.Open lid circuit sensor fault.
Code E6 is flashing on the display.Open lid circuit sensor short circuit.
Code E8 is flashing on the display.Faulty pressure sensor.
Code E11 is flashing on the display.Communication fault between the control and
starting printed circuit boards.
Code E12 is flashing on the display.Communication fault between the receiving and
starting printed circuit boards.
Code E13 is flashing on the display.Float sensor short circuit
Code E14 is flashing on the display.Float sensor fault
Code E15 is flashing on the display.Thermal sensor fault on the receiving printed
circuit board.
Code E17 is flashing on the display.Receiving printed circuit board error.
Code E18 is flashing on the display.Starting printed circuit board error.
The text Pot is flashing on the
display.The removable pot is not inserted.Insert the removable pot into the built-in pot.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Sencor SPR 3900 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
