Bedienungsanleitung Sencor STM 6359 (Seite 9 von 10) (Englisch)

758577

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

04/2021

- 9 -

USING THE COOKIE MAKER ATTACHMENT

1. Place the prepared dough on to the hopper B2. Slide the cookie maker B15 to the left or

right to set the desired cookie shape.

2. Insert the power plug into apower socket. Set the required speed using the speed control

knob A12. When starting it for the rst time, we recommend that you set speed 3 and then

increase or decrease it as required.

3. Use the pusher B1 to push the dough through the feed tube B3. The food processor will

push the dough out in the required shape that you set using the cookie maker B15.

We recommend that you place atray or your palm underneath the pushed out dough. Then

cut the formed dough into smaller pieces.

Attention:

Do not use ngers or other items to push the dough in. Always use the

pusher B1.

4. When you have nished using the food processor, turn it o by setting the speed control

knob A12 to the OFF position.

5. Clean out the attachment after each use according to the instructions in chapter Cleaning

and maintenance.

BLENDING

ASSEMBLING AND DISASSEMBLING THE BLENDER

1. On to the blending jar C4, place the outer lid C2 so that its edges copy the neck of the jar,

and push it down thoroughly along its entire perimeter. Into the hole in the lid C2, place the

inner cap C1 and push it down all the way.

2. Make sure that the food processor is turned o and disconnected from the power socket.

The multi-function head A7 must be tilted down in the horizontal position and the whisk,

beater or kneading attachments must be removed. Release and remove the top attachment

hub cover A6. Place the assembled blending jar on to the top hub and pulling it gently

turn it in the direction of the symbol all the way. The safety mechanism will prevent the

blender from starting unless it is correctly secured to the multi-function head A7.

3. To disassemble proceed in the reverse sequence.

USING THE BLENDER

1. The blender is intended for preparing meals and drinks such as milkshakes, creamy soups,

sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and vegetables,

preparing potato purée, yeast dough or for whipping egg whites.

2. Assemble the blender according to the instructions in chapter Assembling and

disassembling the blender, and put the ingredients (larger pieces need to be cut up in

advance) into the blending jar C4.

Note:

The maximum capacity of the blending jar C4 is 1.5 litres. Never ll it past

the maximum mark. When processing hot liquids or liquids that expand in

volume during the blending process, it is recommended to ll the blending

jar to no more than ⅔ of its maximum capacity.

3. Make sure that the food processor is correctly assembled and that the speed control knob

A12 is set to the OFF position. Connect the power cord to apower socket. Set the required

speed using the speed control knob A12. We recommend to rst set aslower speed to

allow the ingredients to mix together. Then the speed may be increased. The pulse level

is appropriate when you wish to blend food only very quickly. To start the pulse level, turn

the speed control knob A12 to the PULSE position and hold it in this position for amoment.

As soon as you release the speed control knob A12, it will automatically return to the OFF

position.

Attention:

Hot liquids up to atemperature of 55 °C may be processed in the blending

jar. The maximum operating time of the blender is 2 minutes. Do not leave

the appliance in continuous operation for longer than indicated above. Then

allow it to cool down for 30 minutes.

4. While blending, you may add food or liquids to the blending jar C4 through the hole in the

lid C2 after removing the inner cap C1. Never open the outer lid C2 during operation. When

processing hot liquids, the inner cap C1 must remain closed.

5. In the event that food is sticking to the blade assembly C6 or the walls of the blending jar

C4, turn the appliance o by turning the speed control knob A12 to the OFF position and

disconnect it from the power socket. Make sure that the blade assembly C6 has stopped

rotating. Carefully remove the assembled blending jar from the multi-function head A7 by

turning it in the direction of the symbol . Take o the lid and using a plastic spatula,

clean the blade assembly C6 and the inside of the blending jar C4. Put the lid back on and

reattach the blender assembly to the multi-function head A7. Plug the power cord into

apower socket and continue blending.

6. After you have nished using the appliance, set the speed control knob A12 to the OFF

position and disconnect the power cord from the power socket. Check that the blade

assembly C6 has stopped rotating and carefully take the blending jar assembly o the multi-

function head A7. Put the cover A6 back in its place and use asoft plastic spatula to remove

food from the blending jar C4.

7. Disassemble the assembled bowl and clean the individual parts after each use according to

the instructions in chapter Cleaning and maintenance.

ADVICE AND TIPS FOR BLENDING

■ First cut food with a rm consistency such as fruit and vegetables into smaller pieces

measuring 3 cm and only then blend it.

■ First, blend a smaller amount of ingredients and then gradually add more ingredients

through the hole in the lid C2 while blending. In this way, you will achieve better results

than by adding all ingredients into the blending jar C4 at once.

■ If you need to blend food of asolid consistency together with liquids, we recommend that

you rst blend the food of solid consistency and apart of the liquids. Then gradually add the

remaining liquids through the hole in the lid C2 while blending.

■ To blend very thick liquids, we recommend using the pulse level so that the blade assembly

C6 does not get jammed too often. Start the blender repeatedly in short intervals.

■ Ice cubes must be processed immediately upon being removed from the freezer. When the

ice starts to melt, the ice cubes will stick together and it will not be possible to blend them.

QUICK GUIDE TO PROCESSING INGREDIENTS

Ingredients Speed selection Recommended

blending time

Fruit, vegetables cut into smaller pieces 5–6 30 s

Baby food 5–6 40 s

Spreads, dressings, marinades 3–4 30 s

Smoothies and cocktails 6 to MAX 40 s

Soups 6 to MAX 30 s

Ice cubes PULSE

Note:

The above food processing times are only areference. The actual blending

time depends on the size of the ingredients, their amount and the required

nal consistency.

CLEANING AND MAINTENANCE

■ Before cleaning the food processor, always switch it o by setting the speed control knob

A12 to the OFF position and disconnect it from the power socket.

■ Disassemble the food processor into its individual parts. Wait until moving parts come to

acomplete stop before disassembly.

■ Thoroughly wash the used removable parts after every use using warm water with aneutral

dishwashing detergent. Then rinse them under clean running water and wipe them dry with

ane wiping cloth or allow them to dry naturally. After washing and drying, we recommend

to coat the grinding blade B6 and the grinding plates B8, B9 andB10 with cooking oil.

■ If you whisked egg whites, rst rinse the bowl A10 and the beater A4 under cold water.

If you were to use hot water, the egg white remains would harden and their removal would

be more dicult.

■ Clean the mixing container C4 by lling it with 0.5 litre of clean water and afew drops of

kitchen detergent and then assemble the blender and run it for 10 to 15 seconds. Then turn

o the food processor, disconnect it from the power socket, and after the rotating parts have

come to astop, remove the blending jar assembly. Empty out the contents of the blending

jar C4 and then thoroughly rinse out the blending jar C4 with clean water and wipe dry.

■ If more thorough cleaning is required, the cu C5 with blade assembly C6 may be removed

using aspecial wrench that can be ordered free of charge at an authorised service centre.

After cleaning, it is necessary to install the cu C5 with blade assembly C6 back in its place

and to properly tighten it using the wrench.

Attention:

When cleaning, be very careful not to injure yourself on the sharp cutting edge.

■ The metal parts of the meat grinder, the blade assembly C6 and attachments A3–A5

are not intended for washing in adishwasher. Other removable parts may be washed in

adishwasher.

■ For cleaning the base unit A11 and the multi-function head A7, use acloth lightly dipped

in a weak detergent solution. Then wipe everything with a clean dampened cloth and

thoroughly wipe dry.

■ For cleaning, do not use solvents or cleaning agents with abrasive eects. Otherwise, the

surface of the appliance may be damaged.

■ Do not submerge the food processor or its power cord in water or any other liquids.

STORAGE

■ When not using the food processor, store it in a clean, dry place out of children’s reach.

Make sure that the multi-function head A7 is tilted down into the horizontal position.

TECHNICAL SPECIFICATIONS

Rated voltage range ............................................................................................................................... 220−240 V

Rated frequency...........................................................................................................................................50/60 Hz

Rated power input ........................................................................................................................................1 000 W

Noise level .......................................................................................................................................................85 dB(A)

The declared noise emission level of the appliance is 85 dB(A), which represents alevel Aof acoustic

power with respect to areference acoustic power of 1 pW.

Sencor STM 6359 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sencor STM 6359

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info