- 7 - 09/2020
Copyright © 2020, F
EN Bagless vacuum cleaner
User's manual
DESCRIPTION OF
A1 Vacuum cleaner carry handle
A2 Dust container release handle
A3 Dust container lid
A4 Dust container
A5 Hose connection hole
A6 Cord winding button
A7 Suction power control knob
A8 Parking position
A9 On/Off button
A10 Outflow filter protective grille
A11 Outflow filter
A12 Rubber coated wheels
A13 Holder
A14 Sliding flap for air suction
A15 T
A16 T
A17 Combination floor nozzle
A18 Flap position for vacuuming carpets
A19 Flap position for vacuuming hard
(smooth) floors
A20 Stopper for the parking position
A21 Hose
A22 Clip
A23 Hose end
A24 Long flexible crevice nozzle
A25 Combination crevice nozzle with an
extensible brush
ASSEMBL
Inserting the hose into the air suction hole on the vacuum cleaner.
PA5
on the vacuum cleaner until you hear a "click"A21 is now secur
correct position.
Attach the holder to the telescopic tube:
Make sur
tube A15 .
Attach the floor nozzle to the telesc
Make surA17 is attached to the narrower part of the
telescopic tube A15 .
Adjust the length of the telescopic tube:
AA15 as required – disengage and hold the
clip A16 on the tube in the direction shown by the arrow and adjust the length
of the tube A15 as required. A16 and slide out the tube A15
slightly forward until you hear a "click"A15 is now securely
locked in position.
USING THE V
Connecting the vacuum cleaner to the power grid
W
the power plug into a power socket
Attention:
The yellow marking on the power cord warns you tha
cord is close to its end. Do not pull the cord farther than the red
marking.
Adjusting the floor inlet nozzle accor
Y
If you w
If you w
bristles.
T
TA9 .
cleanerA9 again.
Adjusting the suction power
Suction can be contrA7 . T
MAX) increases the pow
MIN) reduces the power
the mechanically sliding flap A14 on the hose handle.
Tips
U
surface. Use the reduced strength when vacuuming upholstery
etc.
If the hose holder becomes blocked when vacuuming
telescopic tube and also disconnect the hose from the vacuum cleaner body
place the holder inside the suction hole on the vacuum cleaner body and vacuum
the stuck dirt out.
T
If you wish tA8
on the vacuum cleanerA20 on the floor nozzle is inserted.
Attention:
Do not move the vacuum cleaner from place to place if the hose
is in the parked position! The st
brake off.
Ending the vacuuming process
When y
Off button A9 and then disconnect the power cord plug from the power socket
T
button A6 with one hand and guide the power cord with the other
Tips
If the winding process stops and part of the power cord is still outside, release the
winding button A6 and pull the cable out again by about 50 cm and then press and
hold the winding button A6 again and repeat the winding process
USING THE
The combination floor nozzle A17 for hard floors ensures perfect and yet gentle
vacuuming of smooth hard surfaces thanks to the brush being from 100 % natural
bristles. It can be used to vacuum floors that are sensitive to scratching such as
wooden or floating floors, marble floors, tiles, linoleum, et
The long flexible crevice nozzle A24 serves to vacuum very hard-to-reach places
anywhere in your car
The crevice nozzle A25 is suitable for vacuuming hard to reach plac
frames, libraries, upholstery corners, joints, etc
CLEANING AND MAINTENANCE
Attention:
Before cleaning, disconnect this appliance from the po
Emptying the dust container
Regularly empty out the dust container A4 as otherwise as the air flow and the suction
power of the vacuum cleaner are reduc
empty out the dust container A4 when you have finished vacuuming
1. A21 .
2. A4 by the handle A2 and pull it out upwards
3. TA4 above a waste bin and press the button for r
the bottom of the dust container – see fig. B , to tip the dirt and dust out of it. If it is
heavily soiled you may wash the entire c
However
4. A4 and insert it into the vacuum cleaner
Attention:
Make sure that all parts are completely dry before reinserting the
dust container A4 back into the vacuum cleaner
Replacement and cleaning of the filtration unit with the HEP
It is recommended to regularly clean and replace the filtration unit with the HEP
to ensure that the vacuum cleaner remains in reliable w
1. A4 out of the vacuum cleaner
2. A3 – see figure C1 .
3. C2 .
Wash both filters under running lukewarm wa
new ones.
4. A4 and wash it together
with the dust container A4 in lukewarm water
5. Then assemble the filtration unit and insert it into the dust container A4 . Then inser
the foam pre-filter and finally the HEPC3 .
6. A4 back into the vacuum cleaner
Attention:
Never insert the filters back into the vacuum cleaner if they are
wet or damp! Always wait until they ar
Replacing the outflow filter
First remove the grille of the outflow filter A10 b
cleaner in the location of both safety clips.
Then remove the outflow filter A11 and replace it with a new one
After reinserting the filter A11 , put on the grille of the outflow filter A10 and click
it in behind both the clips.
