04/2017
- 6 -
Copyright © 2017, F
EN Bagless V
User'smanual
Prior to using this appliance, please r
in cases, when one has already familiarised themselves with previous use of
similar types of appliances. Only use the appliance in the manner described in
this user’smanual
retrieved for future use
We rec
purchase receipt and responsibility statement of the v
for at least the duration of the legal liability for unsatisfactory performance
or quality. In the event of transportation, we rec
appliance in the original box from the manufacturer
DESCRIPTION OF
A1 Handle
A2 Lid
the micro-filter is located under
the lid.
A3 Lid open clip
A4 On/Off button of the vacuum
cleaner
A5 Full dust container indicat
A6 Rubber-coated side travel wheel
A7 Removable 1.3-litre dust
container
A8 Flexible hose connection hole
A9 Lock-in clip
serves to secure the dust
container in the vacuum cleaner
A10 Automatic power cord winding
button
A11 Groove for the horizontal
parking position
A12 Power cord
A13 Removable grill of the outflow
EP
A14 Washable outflow EP
is placed behind the grill.
A15 Front swivel tra
A16 Rear travel wheel
A17 Motor filter
A18 Dust container open clip
A19 Sealing ring
A20 Micro-filter
A21 Flexible hose with mechanical
suction power control in the
handle
A22 T
A23 Floor nozzle with an extensible
brush
A24 Flap for extending and retracting
the brush
A25 Crevice nozzle
A26 Brush nozzle
A27 Upholstery nozzle
INTENDED USE OF
The universal floor nozzle with an extensible brush A23 is intended for all floor
types. Extend the brush when vacuuming smooth hard floors, and retract it
when vacuuming carpets. Use flap A24 to extend and retract the brush.
The crevice nozzle A25 makes vacuuming corners and har
much easier; the brush nozzle A26 can be used for various types of furniture
and nozzle A27 serves to gently vacuum upholstered furniture.
PREP
Make sure that the dust container A7 , motor filter A17 , micro-filter A20 and the
outflow EPA14 are pr
Slide the end of the flexible hose A21 fully into the hole A8 . The hose A21 is
secured in place when an audible click is made.
Note:
Prior to disassembly
A21 while simultaneously pulling it out of the hole A8.
Attach the telescopic tube A22 on to the handle of the flexible hose A21 . Slide
the clip on the telescopic tube A22 in the direction of the arrow marked on the
extension locking clip on the telescopic tube A22 . After unlocking the locking
clip, set the length of the tube A22 by sliding its extensible part in or out. W
the clip is released, it will lock in at the set length.
Connect the floor nozzle A23 to the free end of the telescopic tube A22 .
The crevice nozzle A25 , brush nozzle A26 and upholstA27 can be
attached directly to the handle of the flexible hose A21 or to the telescopic
tube A22 .
USING THE V
Pull on the power plug to wind out the rA12
and connect it to apower socket.
Attention:
The yellow mark on the power corA12 indicates the approaching end
of its length, and the red mark indicates the complete end of its length.
Do not attempt to pull the power corA12 past this mark.
TA4 . Suction power can be set using
the mechanical flap on the handle of the flexible hose A21 .
The rubber-coated wheels protect floating floors against scratching and ensure
smooth motion of the vacuum cleaner on the floor
When you have finished using the vacuum cleaner
A4 and disconnect the power cord A12 from the pow
power cord A12 back into the vA10 until
its entire length is wound upA12 with one hand
while winding it up.
Note:
If the power cord A12 is not wound up complet
A4, and pull the power cord A12 out of the vacuum cleaner b
approximately 50cm and then try to wind it up again.
P
When not using the vacuum cleaner
sliding the guide tab on the floor nozzle A23 into the groovA11 , see fig. B.
Do not carry the vacuum cleaner from place to place if the hose is in the parked
position. TA23 could brake off.
MAINTENANCE AND CLEANING
Before cleaning it, always make sur
disconnected from the power socket.
Emptying and cleaning the dust container
The red-coloured indicator A5 signals that it is necessary to empty out the dust
container A7 .
Release the lock-in clip A9 and pull on the handle A1 to remove the dust
container A7 from the vacuum cleaner
dust container open clip A18 , see figure C1.
and dump out the contents of the container A7 . Gently tap on the sides of
the container A7 to release any ac
recommend emptying out the dust container A7 away fr
Hold the container A7 with one hand and with your other hand turn the handle
A1 in the direction of the open padlock symbol that is marked on the container
A7. Remove the top part containing the cyclone unit from the dust container
A7, see figure C2. A7 under lukewarm running water
and thoroughly wipe it dry.A7 and close its bottom.
Reinsert the assembled container A7 back into the vacuum cleaner and make
sure that it is properly secured in the vacuum cleaner
Cleaning and replacing the motor filter
filter
Remove the dust container A7 from the vacuum cleanerA17
is visibility soiled, tap it out or wash it under lukewarm running water and allow
it to dry naturally. Install the filter A17 and container A7 back int
cleanerA17 is showing signs of wear or it is
heavily soiled, replace it with anew one
Open the lid A2 , remove the micro-filter A20 and tap out its cont
it under aweak current of running lukewarm wat
Make sure that the micro-filter A20 is seated in the sealing ring A19 and put it
back in its place. Close the lid A2 . In the event of heavy soiling or wear and tear
replace the used micro-filter A20 with anew one.
Release and remove the grill A13 . Remove the EPA14 from the vacuum
cleaner
it under aw
dirt out of the folds. Allow the EPA14 to dry naturally
secure it in place with the grill A13 . It is recommended to replace the EP
with anew one after 6 months of use.
When filters are soiled, their eff
cleaning and ensure their timely replacement.
Note:
For h
from living areas.
Attention:
Before putting the filters back into the vacuum cleaner
they are completely dry.
Cleaning the flexible hose, telesc
nozzle and upholstery nozzle.
If the accessories are soiled, take them out and clean away all dirt (dust, hair
animal fur
Cleaning the outer surface of the vacuum cleaner
Clean the outer surface using a
thoroughly dry.
For cleaning the vacuum cleaner
products, solvents etc.
Do not submerge the vacuum cleaner under water or any other liquid and do
not rinse it under running water
