01/2017
- 6 -
Copyright © 2017, F
EN Bagged V
User'smanual
Prior to using this appliance, please read the user’
even in cases, when one has already familiarised themselv
previous use of similar types of appliances. Only use the appliance in
the manner described in this user’smanual. Keep this user’
asafe place where it can be easily retriev
We recommend saving the original car
purchase receipt and responsibility statemen
card for at least the duration of the legal liability f
performance or quality. In the event of transportation, we recommend
that you pack the appliance in the original box fr
DESCRIPTION OF
A1 Removable grill of the outflow
HEP
A2 Washable outflo
is placed behind the grill.
A3 Automatic power c
winding button
A4 Electronic suction power
control
A5 Full dust bag indicat
A6 Flexible hose connection hole
A7 T
releasing clip
A8 Integrated handle
A9 On/Off button of the vacuum
cleaner
A10 Rubber-coated rear trav
wheel
A11 Fr
A12 Groove f
parking position
A13 Groove f
parking position
A14 Dust bag*
A15 Dust bag holder
A16 Grill of the inflow micro-filter
A17 W
is placed in the grill.
A18 Flexible hose with mechanical
suction power control in the
handle
A19 T
A20 Floor nozzle with an
extensible brush
A21 2-in-1 brush and slot nozzle
Note*:
One disposable microfibre (nonw
PREP
Make sure that the dust bag A14 , inflow micro-filter A17 and outflow
HEPA2 ar
Slide the end of the flexible hose A18 fully into the hole A6 .
Note:
When disassembling, it is necessary to press both locking clips at
the end of the hose A18 while at the same time pulling the hose
A18 out of the hole A6.
On to the handle of the flexible hose A18 , place the telescopic tube
A19 and set it to the required length as follo
telescopic tube A19 and slide it towards the e
A19. After releasing the clip, set the length of the tube A19 b
its extensible part in or out. When the clip is released, it will lock in a
the set length.
Connect the floor nozzle A20 to the free end of the telescopic tube A19 .
The flap on the floor nozzle A20 serves to extend and retract the brush.
The 2-in-1 brush and slot nozzle A21 can be attached directly to the
handle of the flexible hose A18 or to the telescopic tube A19 .
USING THE V
Pull on the power plug to wind out the required length of the po
cord and connect it to apower socket.
Attention:
The yellow mark on the power c
end of its length, and the red mark indicates the complete end of
its length. Do not attempt to pull the power cor
TA9 . When vacuuming smooth
hard floor surfaces, extend the brush on the floor nozzle A20 , and
retract the brush when vacuuming carpets.
for vacuuming hard to r
various types of furniture.
Suction power can be set using the electronic control slider A4 or the
mechanical flap on the handle of the flexible hose A18 .
When you have finished using the vacuum cleaner
pressing button A9 and disconnect the power cor
socket.
and hold button A3 until its entire length is wound up Gently hold the
power cord with one hand while winding it up
Note:
If the power cord is not wound up complet
A3, and pull the power cord out of the vacuum cleaner b
approximately 50 cm and then try again to wind it up.
P
When not using the vacuum cleaner
position. For the horizon
the floor nozzle A20 and the groovA13 , see fig. B1 . For the v
parking position, first set the shorA19 .
Then put the vacuum cleaner in a
on the floor nozzle A20 into the grooA12 , see fig. B2 .
MAINTENANCE AND CLEANING
Before cleaning it, always make sure that the vacuum cleaner is turned
off and disconnected from the power socket.
Changing the dust bag
The need to replace the dust bag is signalled by the indicator A5 .
Release the clip A7 and open the top cover of the vacuum cleaner
Remove the used dust bag A14 from the holder A15 and insert anew
bag intended for this type of a
bag is not replaced in time, the vacuum cleaner’
be reduced.
Cleaning and replacing the inflow micro-filter and the outflow HEP
filter
Release the clip A7 and open the top cover of the vacuum cleaner
the grill A16 out of the vacuum cleaner and take the micro-filter A17 out
of it. Rinse it under running lukewarm water and allow to dry naturally
Then reinsert it and close the coverA17
is showing signs of wear or it is heavily soiled
Release and remove the grill A1 . Remove the HEPA2 from the
vacuum cleaner
doing this away from living ar
it under a
washes the dirt out of the folds. Allow the HEPA2 to dry naturally,
then reinsert it and secure it in place with the grill A1 . It is recommended
to replace the HEP
When filters are soiled, their effectiveness is reduced
their cleaning.
Attention:
Before putting the filters back into the vacuum cleaner
sure that they are completely dry
Cleaning the flexible hose, telesc
2-in-1 attachment
If the vacuum cleaner accessories are soiled, remove them from the
vacuum cleaner and clean all dirt off of them (dust, hair, animal fur
Cleaning the outer surface of the vacuum cleaner
Clean the outer sur
wipe it thoroughly dry.
For cleaning the vacuum cleaner
cleaning products, solvents etc.
Do not submerge the vacuum cleaner under water or any other liquid
and do not rinse it under running water
TECHNICAL SPECIFICA
Rated voltage range ...................................................................................220−240 V
Rated frequency ............................................................................................. 50/60 Hz
Rated power input ...........................................................................................1
Maximum power input...................................................................................1
Electrical shock protection class ...............................................................................II
Noise level ......................................................................................................... 81 dB(A)
Dust bag capacity......................................................................................................... 3l
HEP ......................................................................................E12
Length of the power cor .................................................................................... 7 m
Operational radius ................................................................................................. 10 m
