Bedienungsanleitung Sencor SWK 1017 (Seite 7 von 10) (Englisch)

759066

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Electric kettle

SWK 1010WH / SWK 1011GR / SWK 1012BL / SWK 1013OR / SWK 1014RD / SWK 1015VT / SWK 1016YL / SWK 1017TQ / SWK 1018RS

EN-7

2016 07/2016

BEFORE FIRST USE

1. Remove all wrapping material from the kettle and its base.

2. Fill the kettle with clean water up to the maximum water mark. Boil the water and empty the

contents of the kettle. Repeat this process 2 to 3 times.

Note:

To boil water in the kettle proceed according to the instructions in chapter Using the kettle.

3. Now the kettle is ready for use and for preparing warm beverages, etc.

USING THE KETTLE

1. Set the desired length of the power cord. Push the power cord into the groove in the base A4. Place

the base A4 on a stable, even and clean surface.

2. Fill the kettle with the required amount of water. The water level must reach at least the minimum mark

(0.3 l) and must not exceed the maximum mark (1 l). You may ﬁll the kettle through the spout or through

the opening after lifting the lid A1. To open the lid A1, press button A2. After ﬁlling the kettle with

water, close the lid A1 and push it down so that it is secured in the closed position.

Warning!

Never ﬁll the kettle if it is located on the base A4.

If the kettle is overﬁlled, then boiling water could splash out.

3. Place the kettle on the base A4. Insert the power plug into the an electrical power socket. Check

that the lid A1 of the kettle is closed.

4. Start the kettle by moving the switch A5 to position I (On). The power On light A8 will illuminate.

Attention:

Do not turn on the kettle if it is empty. The incorrect use of the kettle may negatively affect its

lifetime. If you accidentally turn on the kettle without water, the thermostat will, after reaching

a certain temperature, interrupt the electric circuit and the power On light A8 will turn off. The

kettle can be used again after several minutes, as soon as its stainless steel bottom has cooled

down.

5. As soon as water boils the kettle will turn off automatically and the power On light A8 will turn

off. Before taking the kettle off the base A4, check that it has turned itself off automatically. If it

has not automatically turned itself off, turn off the kettle manually by moving the switch A5 to

position 0 (Off).

Note:

The operation of the kettle can be interrupted at any time by moving the switch A5 to position

0 (Off).

6. Pour the boiled water into a prepared container, cup or mug. Make sure that the kettle remains in

a horizontal position when it is carried, particularly if it is ﬁlled all the way up the maximum mark.

If you wish to open the lid A1 to reﬁll the kettle, ﬁrst empty all the contents from the kettle so that

you are not scalded by the escaping steam.

7. After you ﬁnish using the kettle, disconnect the power cord from the el. power socket. Empty the

kettle and allow it to cool down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SWK 1017 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info