Bedienungsanleitung Sennheiser mm 100 (Seite 15 von 120) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

233006

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Putting the MM 100 into operation

If a certain Bluetooth connection cannot be established, because the corresponding Bluetooth device is switched

off or out of range, you can manually re-establish the connection as follows:

̈ Switch off the Bluetooth visibility of all Bluetooth devices in the vicinity, except for the Bluetooth device you

want to connect to.

̈ Press the Play/Pause button º.

The LED ¿ flashes 3 times per second, indicating that the headset is in searching mode.

When the headset and the Bluetooth device detect each other, the connection is established. A high confir-

mation beep is heard in the headset.

Switching the headset off

The headset switches off automatically 60 minutes after the last Bluetooth connection has ended (idle mode).

To manually switch the headset off:

̈ Press and hold the Play/Pause button º for 2 seconds.

A descending confirmation beep is heard in the headset and the LED ¿ flashes red twice, indicating that the

headset is switched off.

Pairing and volume settings are saved automatically when the headset is switched off.

Pairing the headset

You can pair the headset to up to 8 devices.

Bluetooth devices supporting:

• the advanced audio distribution profile (A2DP), e.g. a music mobile phone, a portable music player or laptop

(Windows Vista with update as of April 2007 or Mac OS X Leopard)

• the hands free (HFP) or headset (HSP) profile, e.g. mobile phones

Once you have paired the headset to a Bluetooth device, the headset automatically connects to the last paired

Bluetooth device each time this device and the headset detect each other.

Pairing to a mobile phone Before pairing to a mobile phone, make sure:

• that the headset’s battery has been charged as described under “Charging the headset battery” on page 7,

• that your mobile phone is switched on and Bluetooth visibility is enabled,

• that the headset is switched off and placed close to the mobile phone (approx. 20 cm or 7”).

To enter pairing mode:

̈ Press and hold the Play/Pause button º for 5 seconds.

The LED ¿ flashes alternatingly in red and blue, indicating that the headset is in pairing mode.

̈ Once the headset is detected by the mobile phone, select “MM 100” and connect.

When the Bluetooth connection is successfully established, the headset is identified as “MM 100” on the

mobile phone display.

The headset saves up to 8 Bluetooth connection profiles of Bluetooth devices with which it has

been paired. If you want to re-establish a connection with a device with which the headset has

been paired, the connection needs to be established from this device (for details, refer to the

manual of the Bluetooth device). Before doing so, make sure that the last paired device is discon-

nected.

2 s

5 s

If the headset is already switched on and is in standby or idle mode, you can enter pairing mode

by pressing and holding the Next button » or Prev. button · for 5 seconds.

Kopie von 090603_MM100_532892_0409_SP7_PRT.pdf 15Kopie von 090603_MM100_532892_0409_SP7_PRT.pdf 15 04.11.2009 11:16:4404.11.2009 11:16:44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sennheiser mm 100 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info