Bedienungsanleitung Senseair aSENSE M III (Seite 7 von 14) (Englisch)

735538

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Display modes

In DISPLAY MODE the DEFAULT operation is that the sensor alternates between carbon dioxide and

carbon monoxide readings presentation. The push button MENU(+) is used to select the indicated

value on the display to be the error code or the set points of temperature and CO

After power up the

display will always return to the Default display mode. If a permanent change of default values is

requested the PC software is to be used.

Function

Line

Display

Time

limit

Function description

CO / CO

DEFAULT - Normal operation

Exxx

yes

Error code. If no error has been detected the code E0 is shown. The

error code is reset with Entr(+-).

Present CO

and CO

set points

Toggle between display of temperature and CO

set point with

MENU(+).

Table III. On the display without entering the maintenance menu

Maintenance level

A number of execution options are available from the MAINTENANCE MENU (see Table IV). This level

is accessed only from the display mode in the set points of CO and CO

selection. A two buttons push

and an access code restrict access, intended for competent trained service personnel only. The Entr(+-

)command is done by PUSHING MENU AND ESC AT THE SAME TIME (hold down for about 14

seconds). The access code has eight binary digits; one press at MENU(+) equals 1 and one press at

ESC(-) equals 0. The code value can be changed for your personal choice from the software UIP 4.3.

Always use the ESC button to return to the DEFAULT mode. Several pushes of the ESC button may

be needed to return to the DEFAULT mode. The Entr(+-) push (MENU & ESC) eventually leads to

execution of functions, which causes temporary or permanently change of any parameter, that affects

the system outputs!

Function

Line

Display

Time

limit

Function description

ECxx

yes

Access code to the service menu The default value of the code is

255 (=11111111, that is eight presses on MENU(+)). Press down

MENU(+) and let it scroll until it stops. The last two digits of the code

are shown. Then ENTER to accept the selected code.

SPCO

yes

For setting the set point of the CO concentration.

The present

CO set point

yes

For increase / decrease of the CO set point. The set point is

increased by stepping with MENU(+) button. Decreasing is done by

stepping with the ESC(-) button.

SPc

yes

For setting the set point of the CO

concentration

The present

set point

yes

For increase / decrease of the CO

-concentration set point The

set point is increased by stepping with MENU(+) button. Decreasing

is done by stepping with the ESC(-) button.

AOUt

yes

First step of adjusting the analogue outputs MAX and MIN values

An xx

Select analogue output by stepping with MENU(+) button

6c1

SetL

Leads to adjustment of the MIN value.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Senseair aSENSE M III Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Senseair aSENSE M III

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info