Bedienungsanleitung Senseair pSENSE II (Seite 2 von 2) (Englisch)

735546

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

AUTO POWER OFF

Fig.14

The meter turns off automatically after 20 minutes of inactivity.

To override the function, first, the meter is in power off status.

Hold down and for two seconds to turn on the meter

until “n” appears (Fig.14).

SET

ON/ OFF

HOLD

NOTE:

Auto sleep function will be disabled during calibration &

auto recording mode. Auto sleep function WILL NOT be

disabled automatically via using adaptor.

The sensor has an automatic calibration function to secure long-term accuracy. If a

calibration is desired anyway, press simultaneously for three seconds to

turn on the meter and enter calibration mode. Press or key to select 400ppm

CO2 calibration (Outside Air calibration). Press to start and see“CAL” and CO2

value blinking on LCD. Wait about 10 minutes until the blinking stops and the

calibration is completed and back to normal mode. When choosing 0ppm CO2

calibration, remove the cap from meter rear side and plug the CO2 CALIBRATOR pipe

into the sensor hole beneath. Wait about 10 min until the blinking stops and the

calibration is completed and back to normal mode.

MAX/AV G

Humidity Calibration

This meter can be calibrated either via 35% & 80% salt bottle or humidity generator.

The ambient condition is recommended as stable 25 C. While the meter is powered

off, plug the sensor probe into 35% salt. Press , , simultaneously for three

seconds to turn on the meter and enter calibration mode. Press or to select

35.0% calibration and press to start. “CAL” and calibrating value are blinking on

the LCD.

CAUTION:

Do not calibrate the humidity without the default calibration salt. Otherwise,

it will cause permanent damage. Contact SenseAir for calibration salt or

services.

Single point calibration will cause error code E11 or non-accurate reading.

Always do dual point calibration to complete a process. Suggest to calibrate

low humidity first.

CO2 Calibration

CAUTION:

Do not calibrate the meter in the air with unknown CO concentration.

Otherwise, it leads to inaccurate measurements.

Ensure the batteries are fully charged during the calibration to prevent

interruption or failed calibration. When the accuracy becomes a concern

after long time usage, return to dealers for standard calibration.

Technical Data

Humidity/accuracy:

Trouble Shooting

Error Messages Solution

E01

E33

E02

E 03

E 04

E11

E 31

E32

E33

Temperature/accuracy:

CO2 /accuracy:

Storage and transit:

Operating limit for CO2:

Memory:

Dimensions (LxWxH):

Weight:

Battery type:

DC power type:

PC connection:

CO2 CALIBRATOR: 00-0-0022 Zero Calibration Kit

Optional Accessor y

Art.No.

Batter y low indicator

A battery low icon “ “ appears when the supplied power is too low to maintain a

functional operation. Please plug in the 9VDC adaptor enclosed to charge the batteries.

While charging the batteries, you still can power on the device and operate as usual.

SET

ON/ OFF

START

ESC

MEM

HOLD

MEM

MIN

When meter is powered on , hold down for more than two seconds until entering

meter setup mode. To exit setup, press to return to normal mode.

Press or key to select the program and press key to select.

The programmable setting flashes on display, press or key to select and

press key to confirm. To leave without saving, press key to return.

DATA LOGGING

The meter can automatically record HUMIDITY/TEMP/CO2 for long term environment

monitoring. The memory capacity is 6000 points for each parameter. Users can set up

sampling rate from one second to 4hours, 59 minutes and 59 seconds. The factory

preset rate is 30 second.

START

ESC

REC

Fig.19

CO2

REC

Repeat above to start another run of logging. While the logging

space is full, it shows “FULL”. To terminate data logging, press

for two seconds, -icon stops flashing.

Press key to switch to the mode you want to see. Except the

mode switching function, auto power off, MIN/MAX/AVG,

manual record, hold and recall functions are all disabled during

logging.

REC

START

ESC

MODE

RECALL

Meter Setup

SET

ON/ OFF

START

ESC

HOLD

MEM

MAX/AV G

MIN

HOLD

MEM

MAX/AV G

MIN

START

ESC

P10, 99 points MEMORY clear

P11, choose yes or no

Note:

“ “is displayed while

memory is cleared.

P20, auto LOG data clear

P21, choose yes or no

Note:

“ “is displayed while

memory is cleared.

P30, CO2 ALARM setup

P31, choose from 100

to 9900

Note:

-Factory preset 1400ppm.

-Adjustable scale is every

100ppm

o o

P51, choose C or F

Note:

-Factory preset C

P50, Temp. UNIT setup

P61, choose from

04:59:59 to

00:00:01

Note:

-Factory preset at 30 sec.

-The format is

hour:minute:second

P60, logging sampling RATE

P71, choose from

700 to 1990hpa

Note:

-Factory preset at 1013hpa

-The adjustable scale is

every 1hPa.

P70, PRESSURE compensation

MANUAL RECORDING

REC

MEM

HOLD

MEMORY RECALL

In normal or hold mode, press key for more than two seconds until the -icon

flashes. Press or to scroll the memories. The memory sequential number

displays on main LCD first and reading comes after (Fig.16 &17). Press key to

switch the display parameter (Fig.18).The time displayed in memory recall mode is

the recording time of this entry.

Recall

HOLD

MEM

Fig.15

REC

MODE

RECALL

Fig.16

Recall

Fig.17

CO2

Recall

Fig.18

Recall

%rh

MODE

RECALL

After sampling rate is selected, press for two seconds under normal mode to start

logging. The -icon flashes to indicate the logging status and LCD main display

shows the real time value. Lower displays are real time clock (Fig.19).

To setup the sampling rate, when meter is powered on , hold down for more than

two seconds until entering meter setup mode. Press or key to select the

program P60 (rAtE) and press key to enter.

Press or to select the sample rate from hour, minute to second and then press

to confirm. Press to return to normal.

SET

ON/ OFF

MAX /AVG

MIN

START

ESC

HOLD

MEM

MAX /AVG

MIN

HOLD

MEM

The meter features a 99 point memory. In the normal or hold mode, press key

to start recording, the -icon and the main display will be flashed three times. The

memory sequential number will show on the main display with 99 points in maximum.

The data in the memory contains all parameters information and not only the displa-

yed parameter. When all 99 points memory are occupied, a “FULL” message will be

displayed on the screen. If you think the reading is changing too fast, you can press

key to freeze current reading first then manually record the data. This recording

function will be disabled in the MIN/MAX/AVG mode.

P40, CO2 ABC setup

P41, Choose on or off

Note:

-Factory preset ABC

function as ON

SET

ON/ OFF

START

ESC

MEM

HOLD

MEM

MAX/AV G

MIN

SenseAir AB

Stationsgatan 12

Box 96

820 60 Delsbo

Phone: +46(0)653-71 77 70

Fax: +46-(0)653-71 77 89

0.1% to 99.9%/ ±3.0%(10~95%@25 °C), ±5% (other)

o o o

-20 to 60 C/+0.3 C@5~40 C

0 to 9999ppm/+(30ppm+5% of reading)@0~5000ppm

-20 to 60 C/10 to 90%rh, non-condensing.

o o

0 to 50 C, non-condensing / Electronics: -20 to 60 C

99 manual records, 18000 data logging records.

234x77x42 [mm]

200g

Four pcs AA re-chargable batteries

9VDC, 500mA (Standard accessory).

mini USB port

Turn off meter and re-start again

or re-charge the battery

Retry CO calibration

Put meter in normal condition

Solve the original data error

Retry humidity calibration

Return for repair

CO2 sensor is out of order

or the battery is too low

CO sensor is out of order

measured value is under range

measured value is over range

Original data error results in

this error (DP, WB)

RH calibration error

Temp. sensor or AD damaged

Memory IC damaged

RH sensor or circuit damaged

P81, choose 12 or 24

hour format

Note:

-Factory preset at 12H &

dd-mm-year format.

P80, REAL TIME CLOCK setup

choose DATE

format

Input Year/

Month/ Day

year

month

date

Input Hour/

Min./Sec.

Hour

Minute

Second

Senseair pSENSE II Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Senseair pSENSE II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info