Bedienungsanleitung Sentiotec CK 3 (Seite 35 von 56) (Deutsch, Englisch)

753050

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Installation instructions for trained electricians only

5 Variant 1

Install bench sensor FII

Figures 5 7

Install the bench sensor in the sauna cabin about 15

cm below the ceiling and opposite of the heating sys-

tem.

The bench sensor with its overtemperature fuse may

only be connected with the supplied 150° C tempera-

ture-resistant connecting line or an equivalent tempe-

rature-resistant line.

On the outside of the sauna cabin, the temperature-

resistant connecting line can be extended with custo-

mary lines.

WARNING - Electric shock:

Run the power cables separate to other sen-

sor and control lines.

Protect single insulated lines with a pipe

(double insulation).

1. Run line 5 to mounting location of bench sensor

4 in the cabin wall and fix in position with wiring

clips.

2. Separate two half shells 1 of bench sensor 4

and connect two terminals of the up to 150° C

temperature-resistant line according to circuit dia-

gram 7.

3. Insert round adapter plate 2 with the connections

crosswise in half shells 1, close half shells 1

and fix with the two 9 mm long Philips head screws

Check for secure fit of bench sensor 4.

4. Conduct tests according to the chapter “Tests”.

5 Fix bench sensor 4 to the cabin wall opposite of

the heating system with two wood screws 6

keeping a distance of 15 cm to the ceiling.

4 Installing the stove sensor FI

with overtemperature fuse

Figures 4 7

Install the stove sensor with overtemperature fuse in

the sauna cabin about 15 cm below the ceiling and

above the heating system, or in accordance with the

cabin manufacturer's specifications.

Use only the supplied 150° C temperature-resistant

connecting line or an equivalent temperature-resistant

line to connect the stove sensor with overtemperature

fuse.

On the outside of the sauna cabin, the temperature-

resistant connecting line can be extended with conven-

tional lines.

WARNING - Electric shock:

Run the power cables separate to other sen-

sor and control lines.

Protect single insulated lines with a pipe

(double insulation).

1. Run four-pin line 5 to mounting location of sto-

ve sensor 4 in the cabin wall and fix in position

with wiring clips.

2. Separate two half shells 1 of stove sensor 4

and connect four terminals of the temperature-re-

sistant line according to the circuit diagram 7

(observe the color coding on the sensors which

correspond to the figures).

3. Insert round adapter plate 2 with the connections

crosswise in half shells 1, close half shells 1

and fix with the two 9 mm long Philips head screws

Check for secure fit of stove sensor 4.

4. Conduct tests according to the chapter “Tests”.

5. Bolt stove sensor 4 to the cabin wall in alignment

with the heater, keep a distance of 15 cm to the

ceiling, or install in accordance with the cabin

manufacturer's specifications, using two wood

screws 6.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sentiotec CK 3 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info