Bedienungsanleitung Sephra CF18H (Seite 10 von 22) (Englisch)

603254

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

PARTS & FEATURES

(SEE ILLUSTRATIONS ON PAGES 4-7)

All models:

1. Crown—Rests on top of the stabilizer (4)

or cylinder (3a).

2. Top Tier—Slides into place after

positioning the bottom tier (6).

3. Full Cylinder (Signature model only)—

Stands on top of positioning pegs (7a) in

the center of the basin.

3a. Top Section of Cylinder (excluding

Signature model)—Attaches to the

bottom cylinder (3b).

3b. Bottom Section of Cylinder (excluding

Signature model)—Stands on top of the

pegs in the center of the basin (7a).

3c. Cylinder Sleeves—Slide over basin pegs

(7a) to hold cylinder in place.

4. Stabilizer (Signature model only)—Slides

over the top of the cylinder and holds the

top tier and crown in place.

5. Auger—Fits inside the cylinder and

carries fondue to the top of the cylinder,

creating a constant flow of the fondue from

the top of the crown into the basin.

6. Bottom Tier—Slides into position on the

cylinder (3 or 3b).

7. Stainless Steel Basin—Holds the fondue.

The Signature, Elite, and Classic models

hold 4–5 pounds of chocolate (7–9 cups).

The Select model holds 3–4 pounds of

chocolate (5–6 cups). This basin is

removable in the Signature and Elite

models.

7a. Basin Pegs—Hold cylinder in place.

8. Fountain Base—Housing that surrounds

electrical components including the motor

and the electrical circuit board.

8a Vent Holes (excluding Select model)—

Allow hot air produced by the motor and

heating element to escape, cooling the

electrical components. The vent holes

should not be covered.

9. Slip-Resistant Legs (excluding Select

model)—Reduce movement during use

and help prevent marks on tables and

countertops.

10. Adjustable Feet—Screwed into the bottom

of the base. Can be tightened or loosened

to raise or lower a particular side of the

fountain, adjusting its level.

11. “Whisper Quiet” Motor (not pictured)—

Inside fountain housing (8). Designed to

be as quiet and unobtrusive as possible.

Some motor and moving parts noise is to

be expected. The motor is equipped with

an automatic shut-off in the event that

the fountain overheats.

Signature and Elite models only:

12. Control Panel—Regulates all functions

of the fountain.

12a. ON/OFF/POWER button—A green LED

light will be lit when the power is ON.

12b. START button—Starts the motor, causing

the auger to spin inside the cylinder. A

green LED light will be lit when the START

button has been pressed and the auger is

spinning.

12c. HEAT button—Changes the temperature

settings. Each time the button is pressed,

the heat will cycle to the next temperature

setting, moving from OFF to HIGH. A red

LED light will be lit at each temperature

setting except the OFF position, where the

LED light is yellow. The red LED light will

blink intermittently as power is supplied

to the heating element.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sephra CF18H Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sephra CF18H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info