Bedienungsanleitung Severin KS 9788 (Seite 14 von 40) (Deutsch, Englisch, Holländisch, Französisch)

603085

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

position it next to any heat sources (radiators, cookers etc.). If

this cannot be avoided, however, suitable insulation must be in

installed between the heat source and the unit.

∙ The unit must not be installed inside a cabinet, nor directly

below a hanging cupboard, shelf or similar object.

∙ In the case of uneven ﬂ oors, the adjustable feet on the unit

can be used to compensate and ensure optimum stability.

Set-up dimensions

If the refrigerator is installed with its side against a wall, ensure a

minimum clearance of 60 mm to ensure that the door can open

through 90°.

To remove the fresh-storage compartment, the bottle rack must be

taken out ﬁ rst.

Ventilation

The heated air around the rear of the unit must be able to

circulate freely. Therefore, ensure that the air circulation behind

the unit is not obstructed.

Caution: Ensure at all times that the rear ventilation

openings around the top cover are not obstructed.

Reversible door

If required, the door may be reversed, i.e. from right-hinged (default

installation) to left-hinged.

To avoid the risk of personal injury or damage to the unit, two people

are needed to reverse the door.

Warning: Always disconnect the unit from the mains before

any maintenance or repair work is carried out.

Before you get started, please note the following:

∙ Always ensure that the correct number of washers is used on

all hinge bolts and screws.

∙ So that the doors can close tightly against the frame, take the

utmost care that they are properly aligned during re-assembly.

∙ Open the refrigerator door.

∙ Remove the four covers C from the housing and inside of

the door

∙ Replace the covers and their extensions, turned through

180°, on the opposite side.

∙ Unscrew the hinge bolt on the inside of the door in the area

C/6 .

Caution: Support the door.

∙ Take off the refrigerator door.

∙ Take out the ﬁ xing screws and remove the upper bracket 6.

Note the small plastic plate underneath the bracket.

∙ Turn the bracket 6 including the small plastic plate through

180° and replace it on the other side of the refrigerator,

using the two screw holes adjacent to each other.

∙ Remove the lower panel 1.

∙ Unscrew the hinge bolt 2, together with the washers, from

the bracket 7, and ﬁ t it into the corresponding opening on

the opposite side of the bracket 7.

∙ Place the refrigerator door onto the hinge bolt 2 on holding

bracket 7.

Caution: Support the door.

∙ Re-insert the hinge bolt of the bracket 6 into the refrigerator

door.

∙ Fit the four covers C over the bracket and the openings.

∙ Take out the cover 10 from the lower panel 1 and replace it

on the opposite side.

∙ Replace the panel 1 on the appliance.

∙ Remove the screw covering caps a and the sealing plugs b.

∙ Take out the screws holding the door handle. Fit the handle

on the opposite side, using the ﬁ xing screws to secure

it. Push the sealing plugs (provided) into the now empty

openings in the door and replace the covering caps on the

screw heads.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin KS 9788 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info