Bedienungsanleitung Severin KS 9836 (Seite 12 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Finnisch)

712713

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

∙ The product data sheet contains details of the ambient

temperature range suitable for this appliance.

∙ Do not use the appliance outdoors.

∙ Ensure that the plug is accessible and can be removed from

the wall socket at any time.

∙ Do not expose the appliance to direct sunlight, and do not

position it next to any heat sources (radiators, cookers etc).

If this cannot be avoided, however, suitable insulation must

be in installed between the heat source and the unit.

∙ The unit must not be installed inside a cabinet, nor directly

below a hanging cupboard, shelf or similar object.

∙ Ensure that the door can swing open to an angle of 160°.

∙ In the case of uneven ﬂ oors, the adjustable feet on the unit

can be used to compensate and ensure optimum stability.

Ventilation

Ensure that there is enough space around the unit so that the

air circulation round and behind it is not obstructed. (Rear and

sides 5 cm, top 10 cm.)

Reversible door

If required, the door may be reversed, i.e. from right-hinged (default

installation) to left-hinged.

Warning: Always disconnect the unit from the mains before

any maintenance or repair work is carried out.

1. Remove the two screw covers (11) and the screws (10).

2. Remove the entire top panel (9).

3. Remove the three threaded bolts (6) securing the upper

hinge plate (5) on the right-hand side.

4. Carefully lift up the door and place it on a suitable surface

to protect it from scratches.

5. Take off the protective corner-piece (7) and re-ﬁ t it in the

groove on the right-hand side, pushing it ﬁ rmly down.

6. Remove the hinge pin from the upper hinge plate (5) and

screw it back in from the opposite side.

7. Remove the two screws from the left-hand side in the

upper hinge plate mounting and re-ﬁ t them on the right.

8. Remove the three screws (1) holding the lower hinge plate

(2) on the right-hand side.

9. Remove the hinge pin from the lower hinge plate and re-ﬁ t

it in the next hole.

10. Remove the adjustable foot (4) from the left-hand side and

re-ﬁ t it on the right.

11. Attach the lower hinge plate (2). Do not tighten the screws

for the moment.

12. Replace the door in its new position. Ensure that the hinge

pin is inserted into the guide bushing (hole) on the lower

part of the door frame.

13. Attach the upper hinge plate (5) (removed earlier in step 3)

on the left-hand side. Ensure that the hinge pin is inserted

into the guide bushing (hole) on the upper part of the door

frame. Do not tighten the screws for the moment.

14. Adjust the closed door to its proper position and tighten

the screws of the upper and lower hinge plates.

15. Replace the top panel (9).

16. Replace the screws (10) und the screw covers (11) in the

top panel (9).

17. Put the unit back in its intended position and wait for about

two hours before connecting it to the mains.

Freezer compartment door

1. Open the door

2. Insert a screwdriver into the slot under the lower hinge,

push the spring up and hold it.

3. Remove the door and hinge assembly.

4. Take off the protective cover from the left-hand side and

re-ﬁ t it in the opening on the right-hand side.

5. Turn the door round 180°, place the lower hinge onto the

lower door pin and insert the upper door pin into the upper

hinge.

6. Now slide the lower hinge into the corresponding opening,

ensuring it locks into place.

Temperature control

The unit is re-activated by

connecting it to the mains. It

is only switched off completely

when the plug is removed from

the wall socket.

The temperature in the refrigerator cabinet can be adjusted by

setting the temperature control. Turning the control clockwise

will decrease the temperature, while turning it anti-clockwise

will increase it.

∙ After switching on, the temperature control should be set to

its maximum setting.

∙ After 30 minutes, the setting should be changed to a

medium setting, usually sufﬁ cient for home use.

Following a power interruption, or if the unit has been switched

off on purpose, it may take 3 to 5 minutes before it switches

on again.

In position ‘0’, the cooling function is switched off, though

the appliance is still connected to the mains.

Interior lighting

Changing the light bulb:

∙ Remove the plug from the wall socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin KS 9836 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info