Bedienungsanleitung Severin KS 9865 (Seite 33 von 64) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

556609

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Preparing the appliance for operation

! It is recommended to prepare the appliance for operation with a helper.

 Remove package. Lift the appliance away from foamed polystyrene base. Tear off adhesive tapes.

 When positioning the appliance in chosen location, it will move more easily into position if you lift the front a

little and incline it backward, allowing it to roll on its casters.

 Remove all red-coloured parts from the

shelves (

fig. 2). Tear away the red-

coloured adhesive tapes from the door

trays – they are intended only for the

transport of the appliance.

NOTE. When you open the freezer

compartment door a little red packing

detail will fall out – IT IS FOR TRANSPORTATION PURPOSES ONLY.

 Suitably dispose the packaging material.

 Take two supports from the bag and insert them into the guides at the top back

part of the appliance.

►

Positioning

 Place the appliance in a dry, well ventilated room.

 WARNING! The appliance should not be operated in an unheated room or porch. Place the appliance away

from heat sources such as kitchen stove/oven, radiators, or direct sunlight.

 WARNING! The appliance must not touch any pipes for heating, gas or water supply, or any other

electrical devices.

 Do not cover the ventilation holes at the top of the appliances– it must be a good air

circulation around the appliance. There should be a gap of at least 10 cm between the

top of the appliance body and any furniture that may be above it (

fig. 5). If this

requirement is not followed, the appliance consumes more electrical energy and its

compressor may overheat.

◄ If the appliance is placed in a corner,

a gap of at least 1 cm must be left

between the appliance body and the

wall so that the freezer compartment

door can be opened enough to pull out

the frozen product drawer.

 The appliance must stand on a level

surface and must not touch the wall.

If necessary, regulate the height of

the appliance by adjusting the

levelling feet: by turning them

clockwise – the front of the appliance

rises, by turning them counter clockwise – it comes down. If

the appliance is tilted slightly backward – the doors will

close by themselves.

Changing the interior light bulb

When changing the interior light bulb, do the actions below in the order they are

listed:

Unplug the appliance from the mains by pulling the plug out of the

electricity supply socket

2. Squeeze the sides of the light fixture cover

1 to unhook the cover fasteners A

and pull downward. Remove the cover.

3. Replace the light bulb with the same 15 W type light bulb with the E14 lamp holder.

4. After changing the light bulb, put the cover fastener hook in place

B and then press upward until it’s fixing

in place. Plug the appliance into the electricity supply socket.

KS 9870 / 71 KS 9897 / 98 / 99 / 9770

KS 9865 / 66 / 67 / 68 KS 9874 / 72 / 73KS 9865 / 66 / 67 / 68 KS 9874 / 72 / 73

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin KS 9865 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info