Bedienungsanleitung Severin KS 9901 (Seite 15 von 40) (Deutsch, Englisch, Holländisch, Französisch)

712706

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Caution: Ensure at all times that the rear ventilation

openings around the top cover are not obstructed.

Reversible door

If required, the door may be reversed, i.e. from right-hinged (default

installation) to left-hinged.

To avoid the risk of personal injury or damage to the unit, two people

are needed to reverse the door.

Warning: Always disconnect the unit from the mains before

any maintenance or repair work is carried out.

Before you get started, please note the following:

∙ Always ensure that the correct number of washers is used

on all hinge bolts and screws.

∙ So that the doors can close tightly against the frame, take

the utmost care that they are properly aligned during re-

assembly.

∙ Remove the two spacers (2) on the rear of the unit.

∙ Open the freezer door (18).

∙ Remove the ﬁ xing screws (1 and 3) from the top cover (two

screws at the front and two at the rear), and take off the

cover (4).

∙ Unscrew the upper hinge bracket (5) and remove it.

Caution: the door must be supported while this is done.

∙ Take off the freezer door (18).

∙ Unscrew the hinge pin (7) together with the nut (6) and

washers (8), and ﬁ t the entire assembly to the opposite side

of the hinge bracket.

∙ Undo the ﬁ xing screws (11) on the centre hinge bracket (10)

and take them off, together with the washers (12).

Caution: Support the door.

∙ Take off the centre hinge bracket (10) together with the

hinge pin washers and the plastic plate (9).

∙ Take off the refrigerator door (13).

∙ Tilt the whole unit towards the rear.

∙ Unscrew the lower hinge bracket (14) and take it off.

∙ Unscrew the hinge pin (15) from the bracket, and re-insert it

from the other side.

∙ Remove both screws on the left of the underside and

replace them on the right.

∙ Fit the lower hinge bracket (14) on the left of the underside.

∙ Put the washers on the hinge pin.

∙ Remove the cap (19) from the freezer door and the cap (16)

from the refrigerator door and replace them on the opposite

side of the doors.

∙ Take off the caps (17) from the partition between the

refrigerator and freezer compartments and remove the

screws.

∙ Replace both screws on the opposite side and then the

caps.

∙ Fit the refrigerator door (13) onto the pin (15) of the lower

hinge bracket.

∙ Fit the pin of the centre hinge bracket (10), together with the

washers, to the refrigerator door (13).

∙ Fit the centre hinge bracket (10) together with the plastic

plate (9).

∙ Remove both screws from the upper left and replace them

on the right.

∙ Place the freezer door (18) onto the pin of the centre hinge

bracket (10).

∙ Fit the pin of the upper hinge bracket (5) to the freezer door

(18), and then

ﬁ t and secure the upper hinge bracket (5).

Note: If necessary, the alignment of the doors can be adjusted

by slightly loosening the hinge bracket screws, but remember

to tighten them afterwards.

∙ Replace the top cover (4) and use the screws (1 and 3) to

secure it (two screws at the front and two at the rear).

∙ Fit the two enclosed spacer elements (2) into the

corresponding guide slots on the rear).

If the unit has been tilted to more than 30°, wait for about 4

hours before re-connecting it to the mains.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin KS 9901 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info