Bedienungsanleitung Severin PG 8106 (Seite 12 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

761777

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

142 x 208 mm

∙ The grill must not be used with any core thermometers

other than the ones supplied.

∙ No responsibility is accepted if damage results from

improper use, or if these instructions are not complied

with.

∙ This product complies with all binding CE labelling

directives.

Before using for the rst time

∙ Remove any packaging materials and stickers from the

appliance.

∙Cleanthegrillrack,reectortray,thetrayinsertsand

wind-guard with warm soapy water; wipe thoroughly dry

afterwards.

∙ Assemble the appliance as described in Preparing the

unit.

∙ Let the grill heat up for approximately 10 minutes at

maximum power without any food (see ‘Boost-zone’

grilling). This will remove the smell typically encountered

whenrstswitchingonagrill.Alittlesmokemaybe

emitted; for that reason, adequate ventilation should

be ensured by opening windows or balcony doors; an

extractor hood is also suitable.

Grill assembly

∙ Assemble the grill as shown in the diagrams:

∙Placethereectortrayintothegrillhousing.

∙ Note: Fit the tray inserts so that each insert covers

four protrusions.

∙Fit the heating element with junction box into the

reectortray.Theapplianceisequippedwithasafety

switch. The unit can be operated only with the junction

box properly installed.

∙Fit both grill rack elements so that the studs on the

racktintothecorrespondingopeningsinthereector

tray.

∙Fitthewind-guardelementsrstattherearintothe

recesses on the grill rack, and then secure them on

the grill rack frame.

Grill cart assembly

∙ For grill models with grill cart, assemble the cart as

shown in the diagram.

∙ For assembly, a Phillips screwdriver is needed.

∙ Prior to assembly, check that all parts are complete as

listed in the Familiarisation section.

∙ Assembly:

∙Placethegrillcartframeupside-downontheoor.

∙Insert the four support legs into the housing and

secure each leg with two big bolts. The two support

legswithadditionalwheelopeningsarettedonthe

side without the stainless-steel hooks.

∙Turn the frame with the support legs upright.

∙Fit the plastic frame of the storage rack and secure it

on all four support legs, using the corresponding bolts

andnuts;thentthestoragerack.

∙Slide the wheel axle through the openings on the

support legs and put on the wheels. Secure each

wheel with one of the cotter pins, and clip on the

wheel covers.

∙Fit the side tables onto the corresponding metal pins.

∙If required, hang the towel hooks on the stainless-steel

bar.

∙Ensure that the grill cart is stable. Check the bolts

regularlyforrmconnection.

∙Place the assembled grill on top.

Caution:

∙Do not exceed a maximum load of 3 kg for the side

tables, and 20 kg for the storage rack.

∙ If you need to move the grill, remove the table on the

side opposite from the wheels and grip the frame.

Preparing the unit

∙Assemble the appliance as described in Grill assembly.

For grill models with grill cart, refer to Grill cart

assembly.

∙FillthereectortraywithwatertotheMax marking (max

2 litres). Do not pour water on the heating element or its

sensor.

Hint!

Duringgrilling,thewaterinthereectortrayshouldbe

replenished in good time. Caution: Always disconnect

theappliancefromthemainsbeforere-lling.

∙ Connect the appliance to the mains.

∙ The light ring lights up blue, the unit is ready for use.

Rotary control

The rotary control is used for function selection or switching

off (Sleep mode).

Turn:

Select the Function/Temperature/Timer.

Push - short:

Conrmtheselection.

Push - two seconds:

1 x: return to stand-by mode to change a function

2 x: return to sleep mode

Rotary control - light ring

The light ring indicates the current operating mode:

No light:

The unit is in sleep mode.

Blue light:

The unit is in stand-by mode.

Flashing:

The grill rack has not yet reached the selected temperature.

The unit is heating up or cooling down.

Steady:

The selected temperature has been reached.

Orange:

Grilling 80-320 °C

Red:

Boost-zone 330-500 °C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin PG 8106 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info