556555
9
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
9
Do not touch any moving parts during
operation - this can be extremely
dangerous.
Caution: do not put hot liquid into the
blender jug.
Always switch the appliance off and
remove the plug from the wall socket,
- before opening the lid,
- before removing or tting the
blender jug,
- before cleaning,
- in case of any malfunction during
use,
- after use.
When removing the plug from the wall
socket, never pull on the power cord;
always grip the plug itself.
Caution: Any misuse can cause severe
personal injury.
No responsibility will be accepted if
damage results from improper use, or if
these instructions are not complied with.
This appliance is intended for domestic or
similar applications, such as
- in shops, of ces and other similar
working environments,
- in agricultural working environments,
- by customers in hotels, motels etc. and
similar establishments,
- in bed-and breakfast type environments.
In order to comply with safety regulations
and to avoid hazards, repairs of
electrical appliances must be carried
out by quali ed personnel, including the
replacement of the power cord. If repairs
are needed, please send the appliance to
one of our customer service departments.
The address can be found in the appendix
to this manual.
Before using for the rst time
Before the appliance is used for the rst
time, the blender jug and the lid should
be thoroughly cleaned as described in the
section General Care and Cleaning.
Switch settings
The following settings can be selected:
P The appliance remains switched on as
long as the rotary switch is held in this
position
0 The appliance is switched off
1 Low power
2 Maximum power
Short-term operation
The appliance is designed to process
average domestic quantities of food; it
can be operated without interruption for
a maximum of 60 seconds, after which it
should be allowed to cool down.
Safety switch
A special safety switch in the motor housing
ensures that the appliance can only be
operated once the blender jug and lid are
properly locked in position.
Before removing the blender jug, make
sure that the rotary control is in position 0.
This also applies when
tting the blender
jug to the motor housing. If the control is
not in its off-position (0), the motor will start
immediately.
Operation
Fit the blender jug to the motor housing
with its handle on the right and lock it
by turning anti-clockwise until the lock
symbol and arrow mark are properly
aligned.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Severin SM 3719 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info