Bedienungsanleitung Severin SM 9688 (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Finnisch)

556548

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

∙ No responsibility is accepted if damage

results from improper use, or if these

instructions are not complied with.

Before using for the ﬁ rst time

Remove any packaging materials and check

that all components are present.

Before the appliance is used for the ﬁ rst

time, or after extended periods of non-use, it

should be thoroughly cleaned as described

in the section Cleaning and care.

Operation

We recommend the use of long-life milk

(UHT) with a high protein content. For best

results, the milk should be taken from the

refrigerator immediately before frothing.

The underside of the container and the contact

area on the inside of the base must be clean

and dry.

Choosing the stirring head

∙ Use the smooth stirring head to heat up

milk.

∙ For frothing and heating milk at the same

time, use the serrated head.

∙ For cold-frothing milk, also use the

serrated head.

∙ The head not currently in use can be

stored in the rear of the housing.

Fill amounts

∙ Always observe the minimum mark and

ensure the container is ﬁ lled with at least

120 ml milk.

∙ For frothing, ﬁ ll the container to a

maximum of 350 ml (lower max mark

∙ For heating, ﬁ ll the container to a

maximum of 700 ml (upper max mark ).

Heating up or frothing milk

∙ Place the container onto the base.

∙ Remove the lid from the milk container.

∙ Place the appropriate head onto the

mounting protrusion inside the bottom of

the container.

∙ Put the required amount of milk into the

container.

∙ Place the lid on the container.

∙ Use the temperature control to set the

desired temperature or to select the cold-

frothing function (COLD).

∙ Insert the plug into a suitable wall socket.

A beep signal is heard and the main

indicator lamp starts ﬂ ashing.

∙ Press the On/Off switch.

∙ A double beep is heard, the indicator lamp

remains on and the motor cooling system

starts up.

∙ The stirring process begins. Once the

milk is sufﬁ ciently hot or the cold-frothing

process is complete, both heating and

stirring processes stop automatically.

∙ The main indicator lamp ﬂ ashes, and a

number of beep signals are heard.

∙ You can now remove the milk container

from the base. Use a suitable spoon to

take off the milk froth.

∙ The cooling system continues to run for

a brief period. The main indicator lamp

stops ﬂ ashing after about three minutes.

∙ The power cord can now be disconnected

from the socket.

Remarks

If the appliance has not been disconnected

from the mains , the On/Off switch must be

pressed twice to start a new operating cycle.

After a heating cycle, the appliance

cannot start a new stirring and heating

cycle immediately, but must be allowed to

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin SM 9688 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info