Bedienungsanleitung Sevylor TAHITI (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch, Finnisch)

740985

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

MAINTENANCE : DEFLATING – FOLDING THE BOAT – CLEANING – WINTERING STORAGE

1. Remove paddles and other accessories.

2. To deflate, unscrew the valves’ insert and open the valve cap of the push-in valve.

3. Clean and check the item as well as all the accessories after each use. Rinse it thoroughly making sure that any salt

residues are removed, if it has been used in salt water. Use a mild soapy solution, but do not use detergents or any

type of silicone-based products. Make sure that the product is completely dry before putting it away.

4. Fold the 2 sides into the middle, then roll it up from the opposite end of the valves (so remaining air can escape from

the valves); start again if you feel there is still some air in the tubes.

5. When storing your inflatable, keep it in a clean and dry place, away from extreme temperature variations or other

potentially damaging factors. It can be stored deflated and rolled up in a bag or assembled and lightly inflated. Store it

away from rodents.

HOW TO REPAIR SMALL PUNCTURES

You can repair small punctures with the repair kit supplied. (NOTE: Glue not included in USA.) Please note that in order

for the repair to be successful, the humidity level should be less than 60%, and the temperature between 18°C and 25° C.

Avoid carrying out repairs in the rain or in direct sunlight.

Check that the tube is fully deflated and lies flat.

1. Cut a round patch at least 2” / 5 cm larger than the damaged area.

2. Clean the damaged area and the corresponding side of the patch with an alcohol-based grease remover and allow it

to dry for 5 minutes.

3. Apply 3 thin layers of glue to both the patch and the damaged area; allow it to dry for 5 minutes between layers until

the glue feels tacky.

4. When the third layer of glue is dry, apply the patch without pressing down, and adjust the position if required. Remove

any air bubbles which may have formed under the patch by smoothing the patch with a round object such as a spoon.

Start in the centre of the patch and work towards the outside. Clean off the excess glue with a solvent. Drying : 12

hours.

WARNING !

 Perform repairs in a well-ventilated area.

 Avoid inhaling glue vapours or swallowing the glue.

 Avoid contact with the skin or the eyes.



Keep all repair materials (glue, solvents, etc.) outo

out of the reach of children.

N.B. The seams must not be glued. Only the manufacturer of the boat can perform repairs on the seams.

WARRANTY

Sevylor warrants (legal warranty) to the original purchaser only, and from date of purchase, when any product is used for

normal recreational purposes, that the product is free from defects (weldings). Check with your local Sevylor office for

warranty duration details, which vary for different countries. The warranty does not cover any puncture, cut or abrasion

sustained in normal use or damage from unreasonable uses or improper storage.

If any product is found to be defective, the owner may return it to the store it was purchased from with the

original sales receipt. After inspection of any product found defective, Sevylor shall either repair or replace the defective

part or item as deemed necessary by Sevylor.

Sevylor shall not be held liable for incidental and consequential damages.

There are no warranties which extend beyond the description of the face hereof.

This warranty is inclusive in lieu of all other warranties.

This warranty gives you specific legal rights and you may also have other rights, which may vary, from country to country.

The main limitations to the application of the warranty are the following :

• The item must not be modified and/or fitted with a motor in excess of that allowable by the manufacturer or

used in any activities outside normal recreational use (such as races, rental, professional usage).

• Use in excess of the manufacturers recommended maximum load capacity.

• Pressure recommendations, assembly / disassembly and handling procedures must be strictly observed.

• The maintenance and the storage procedures must not be neglected.

• This warranty does not cover parts and accessories not supplied or recommended by the manufacturer or

defects resulting from the installation of such equipment on their products.

NOTICE : all repairs covered by warranty must be performed by Sevylor.

WARNING !

Your product is designed in accordance with the standards for a specific use. Any modifications,

transformations or use of a motor horse power higher than indicated by the manufacturer could result in serious

risks for the user and will void the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sevylor TAHITI Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info