663255

Shada 800509 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
LED’s
light
A
BRAND
SHADA
LED’s
light
A
BRAND
SHADA
WEEE NL: 3505
WEEE DE: 37281017
WEEE AT: 40133
Imported by
Kanaal Noord 350
NL-7323 AM Apeldoorn
www.shada.nl
Optional: Sensor settings (only for articles: 800509)
DIP switch: ON = 1 / OFF = 0
Time setting:
Light sensitivity activation:
Detection range overview (diameter)
Detection range setting (sensitivity)
Height of installation
Time setting
duration of light after detection
Light sensitivity activation
The lower lux is programmed, the darker it must be to switch
on the ceiling light
Installation and Operating Manual
Art Nr.
Power
Input voltage
LED Lumen output
Color temp.
Microwave Sensor
Lifespan (h)
Dimensions
General safety instructions
Please read the operating instructions for the LED ceiling light
before use. The operating instructions are part of the product.
They contain important notes on start-up and handling of the
device. Always keep the enclosed operating instructions so as
to be able to look up information. They must be enclosed when
passing the device on to third parties.
Safety precautions
The user must observe the safety notes and warnings in order
to maintain this status and to ensure safe operation. Please
read the operating instructions before start up.
Avoid contact with high temperatures or vibrations, this may
cause damage to the ceiling light. Do not immerse the enclo-
sure into water.
Never attempt to open the device other than described in this
manual. The LED ceiling light cannot be repaired; this part
must be immediately disposed in case of a defect. Ensure su-
cient ventilation of the device. Never cover it during operation.
Do not install in reach of children or animals.
Any other use of the device than described above can damage
the product or endanger the user due to e. g. short-circuits, fire
or an electric shock. The entire product may not be modified or
adapted. Don’t touch the ceiling light while in use or after use
until it’s cooled down. The ceiling light must have an earthed
connection for safe operation.
These safety notes must be observed in all cases! Any warranty
claim is void in the case of damages caused by non-observan-
ce of these operating instructions. We are not liable for con-
sequential damages or for damages to property or persons
caused by non-observance of the safety notes and improper
operation of the device.
Safe operation is not possible anymore, if:
- the LED ceiling light has visible damages,
- the LED ceiling light does not work anymore
Installation instructions →
Notes on Disposal
Old units, marked with the symbol as illustrated,
may not be disposed of in the household rubbish.
You must take them to a collection point for old
units (enquire at your local authority) or the dealer
from whom you bought them. These agencies will
ensure environmentally friendly disposal.
Care and warranty
Before cleaning the unit, disconnect it if necessary from other
components; do not use aggressive cleaning agents.
The unit has been carefully checked for defects. If nevertheless
you do have cause for complaint, please go back to the retailer
where you have bought the product together with your proof
of purchase. We oer a 2year warranty from date of purchase.
We are not liable for damage arising from incorrect handling,
improper use or wear and tear. We reserve the right to make
technical modifications.
Visit us online at www.shada.nl for more information about
our products and our company.
CE declaration
This product is according next directives
LVD: 2014/35/EU,
EMC: 2014/30/EU
ROHS: 2011/65/EU
Transmission: R&TTE 1999/5/EC
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Transmission power <0.2mW:
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15℃~+60℃
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detection
range
Detection angle
2.5-3.5m
Min:2m
Max:10m
Height of installation2.5~3.5M
Min:2m
Max:10m
(Height of installation2.5M)
Warning!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
If there is metal material blocking the sensor the device may not
work properly.
productThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIME:S1,S2
S1
1
1
S2
TIME
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Transmission power <0.2mW:
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15℃~+60℃
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detection
range
Detection angle
2.5-3.5m
Min:2m
Max:10m
Height of installation2.5~3.5M
Min:2m
Max:10m
(Height of installation2.5M)
Warning!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
If there is metal material blocking the sensor the device may not
work properly.
productThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIME:S1,S2
S1
1
1
S2
TIME
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Transmission power <0.2mW:
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15℃~+60℃
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detection
range
Detection
angle
2.5-3.5m
Min:2m
Max:10m
Height of installation2.5~3.5M
Min:2m
Max:10m
(Height of installation2.5M)
Warning!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
If there is metal material blocking the sensor the device may not
work properly.
productThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIME:S1,S2
S1
1
1
S2
TIME
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Transmission power <0.2mW:
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15℃~+60℃
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cosφ=1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. You can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detection
range
Detection angle
2.5-3.5m
Min:2m
Max:10m
Height of installation2.5~3.5M
Min:2m
Max:10m
(Height of installation2.5M)
Warning!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
If there is metal material blocking the sensor the device may not
work properly.
productThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIME:S1,S2
S1
1
1
S2
TIME
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01
instruction
YG-01
instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Transmission power <0.2mW:
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15℃~+60℃
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. You can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detection
range
Detection angle
2.5-3.5m
Min:2m
Max:10m
Height of installation2.5~3.5M
Min:2m
Max:10m
(Height of installation2.5M)
Warning!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
If there is metal material blocking the sensor the device may not
work properly.
productThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIME:S1,S2
S1
1
1
S2
TIME
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
800509
18W
230V AC
1.050
3.000K
Yes
25.000
Ø340 x 95mm
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Shada 800509 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info