663255

Shada 800509 Seite 3

3
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
LED’s
light
A
BRAND
SHADA
LED’s
light
A
BRAND
SHADA
WEEE NL: 3505
WEEE DE: 37281017
WEEE AT: 40133
Imported by
Kanaal Noord 350
NL-7323 AM Apeldoorn
www.shada.nl
Hinweise für die Entsorgung
Altgeräte, die mit dem abgebildeten Symbol ge-
kennzeichnet sind, dürfen nicht in den Hausmüll
entsorgt werden.
Sie müssen sie bei einer Sammelstelle für Altgerä-
te (erkundigen Sie sich bei Ihrer Gemeinde) oder dem Händler,
bei dem es gekauft wurde abgegeben werden. Diese sorgen für
eine umweltfreundliche Entsorgung. Importiert von SHADA
BV, WEEE DE: 97413743, WEEE NL: 3505, WEEE AT: 40133
Pflege und Garantie
Bevor Sie das Gerät reinigen, trennen Sie es bei Bedarf von an-
deren Komponenten; Verwenden Sie keine aggressiven, Tensi-
de enthaltenden Reinigungsmittel.
Das Gerät wurde sorgfältig auf Mängel überprüft. Wenn Sie
trotzdem Grund zu einer Beanstandung haben, gehen Sie bitte
zum Händler, bei dem Sie das Produkt gekauft haben zusam-
men mit dem Kaueleg zurück. Wir bieten eine 2 Jahre Ga-
rantie ab Kaufdatum. Wir haften nicht für Schäden, die durch
falsche oder unsachgemäße Handhabung oder Verschleiß. Wir
behalten uns das Recht vor ohne vorherige Information, techni-
sche Änderungen vorzunehmen die der Produktverbesserung
dienen.
Besuchen Sie uns online unter www.shada.nl für weitere Infor-
mationen über unsere Produkte und unser Unternehmen.
CE-Konformitätserklärung
Hiermit erklären wir, dass das Produkt den grundliegenden An-
forderungen des europäischen Parlaments und der Richtlinien
des Rates zur Angleichung der Gesetze der Mitgliedsstaaten
hinsichtlich der Niederspannungsrichtline (LVD), elektromag-
netischen Verträglichkeit (EMC)erfüllt.
LVD: 2014/35/EU,
EMC: 2014/30/EU
ROHS: 2011/65/EU
Funk: R&TTE 1999/5/EC
LED‘s light
Montage- und Bedienungsanleitung
Art Nr.
Eingangsleistung
Eingangsspannung
LED Lumen
Farbtemperatur
Sensor
Lebensdauer (h)
Abmessungen
800509
18W
230V AC
1.050
3.000K
Yes
25.000
Ø340 x 95mm
Optional: Sensor EInstellungen (nur für artikel: 800509)
DIP switch: Eins = 1 / OFF = 0
Zeiteinstellung:
Einstellung Lichtempfindlichkeit:
Erfassungsbereich übersicht (Durchmesser)
Erfassungsbereich (Empfindlichkeit)
Installationshöhe
Zeiteinstellung
Einschaltdauer
Lichtempfindlichkeit
Je niedriger der Luxwert eingestellt wird um so dunkler muss
es sein bis die Lampe einschaltet.
Allgemeine Sicherheitshinweise
Bitte lesen Sie die Betriebsanleitung für die LED-Leuchte vor
dem Gebrauch sorgfältig und vollständig durch. Die Betriebs-
anleitung ist Teil des Produkts. Sie enthält wichtige Hinweise
zur Inbetriebnahme und Handhabung des Gerätes. Verwahren
Sie die beiliegende Bedienungsanleitung um auch späterhin
in der Lage zu sein, nach Informationen suchen können. Wenn
das Gerät verkauft oder an Dritte weitergegeben wird sind Sie
verpflichtet auch Bedienungsanleitung weiter zu geben da die-
se, laut Gesetzgeber, ein Teil des Produktes ist.
Sicherheitsvorkehrungen
Die Sicherheitshinweise und Warnungen sind unbedingt zu
beachten. Um den einwandfreien Zustand des Produktes und
einen gefahrlosen Betrieb zu gewährleisten, lesen Sie bitte die
Betriebsanleitung vor der Inbetriebnahme vollständig durch.
Versuchen Sie nicht das in dieser Bedienungsanleitung be-
schriebene Gerät auf eine andere Art als beschrieben zu öffnen
oder gar zu zerlegen. Die LED-Leuchte kann nicht repariert
werden. Im Falle eines Defektes außerhalb der Garantiezeit ist
das Gerät bei den zugelassen Sammelstellen für Sondermüll zu
entsorgen. Bei der Wahl des Installationsplatzes sollten Sie auf
ausreichende Belüftung des Gerätes achten. Decken Sie das Ge-
rät niemals während des Betriebs ab. Installieren Sie das Gerät
nicht in Reichweite von Kindern oder Tieren.
Jede andere Verwendung des Gerätes als in der Bedienungs-
anleitung beschrieben kann das Produkt beschädigen oder
Gefahren für den Benutzer durch z.B. Kurzschluss, Feuer oder
einen elektrischen Schlag hervorrufen. Das Gerät darf nicht
geändert oder angepasst werden da das Gerät Typgeprüft und
zugelassen ist.
Diese Sicherheitshinweise sind in allen Fällen einzuhalten! Der
Garantieanspruch erlischt im Fall von Schäden, durch Nicht-
beachtung dieser Bedienungsanleitung. Des Weiteren haften
wir nicht für Folgeschäden, Schäden an Gegenständen oder
Personen die durch Nichtbeachtung der Sicherheitshinweise
und unsachgemäßer Bedienung des Geräts verursacht werden.
Ein sicherer Betrieb ist nicht mehr möglich, wenn:
- Die LED-Leuchte sichtbare Schäden aufweist
- Die LED-Leuchte nicht mehr funktioniert
In diesem Falle ist die Leuchte außer Betrieb zu setzen.
Montageanleitung →
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. You can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. You can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Shada 800509 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info