Bedienungsanleitung Shark EP035 (Seite 3 von 4) (Englisch)

668669

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

OPERATING INSTRUCTIONS cont.

GETTING TO KNOW YOUR SHARK HAND VACUUM

Cleaning & Changing the

HEPA Dust Cup Filter

Warning: Always unplug the unit from

electrical outlet before opening the Dust

Cup (container).

Important: Do NOT use the HEPA filter

cartridge without the debris screen in

place.

Warning: After each Use - Always

remove the Filter Debris Screen from the

HEPA Dust Cup Filter, then vigorously

“TapClean” HEPA Filter until no more

dust can be removed.

Fig. 4

Fig. 3

Debris

Screen

HEPA Filter

PLEASE NOTE

: The white pleated

filter material in the HEPA Dust Cup

Filter will discolor over time -This is

NORMAL and will NOT affect the

performance of the filter. If the HEPA

Dust Cup Filter

is properly

"TapCleaned”

after each use

and suction

does not return

to 100%, then

we suggest that

the HEPA filter

be “TapCleaned”

vigorously until no

more dust can be removed, then

rinsed under the faucet and allowed to

dry for 24 hours before refitting into

the vacuum. (Fig. A) Wash once a

month or when suction appears

reduced.

5. Vigorously “TapClean”

the HEPA Dust Cup

Filter on a hard

surface until no more

dust is observed

falling out from

between the pleats of

the filter. (fig. 4)

Fig. 5

Debris

Screen

6. “TapClean” the Debris

Screen or rinse under

a faucet until clean.

(fig. 5) Remember that

the Debris Screen

must be completely

dry before reinstalling

in the vacuum.

7. Replace the Debris Screen on the

HEPA Dust Cup Filter and reinstall

filter assembly in the vacuum. (not

shown)

Fig. A

Wash once a

month or when

suction

appears

reduced.

Warning: Allow 24

hours for drying before

replacing in unit.

HEPA FilterDebris Screen

IMPORTANT

, Please Note : The

“TapClean” HEPA Dust Cup Filter &

Debris Screen will stop most of the tiniest

dust particles and airborne allergens from

re-entering the air you breathe. In fact it

stops 99.97% of all particles as small as

0.3 microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Dust Cup

Filter will quickly accumulate, inside the

white filter folds, many fine dust particles

that are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly. Clean the

HEPA Filter and Debris Screen after each

use as described in this section.

1. To open the Dust Cup (container),

push button and detach the Dust

Cup (container ). (Fig. 1)

2. Pull out the HEPA Dust Cup Filter.

(Fig. 2)

Fig.2

Fig. 1

6. Suction Hole

7. Shoulder Strap

8. Pet Hair Removal Attachment

9. Cleaning Brush

10. Flexible Hose

11. Hepa Filter Assembly

1. Dust Cup Release Button

2. On/Off Power Switch

3. Handle

4. Intelli-Sense Filter Monitor

5. Dust Cup (Container)

3. Empty the dust from the Dust Cup

(container).

4. Separate the debris screen from the

HEPA filter cartridge by grasping the

debris screen with one hand and the

filter frame with the other and pull

apart. (fig. 3)

Technical Specifications

Voltage: 120V., 60Hz.

Power: 6.67 Amps, 800 Watts

CAUTION: The suction hole must be

open, free of any obstructions at all

times. Otherwise, the motor will overheat

and could become damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Shark EP035 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info