Bedienungsanleitung Shark IF250 (Seite 20 von 24) (Englisch)

743230

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

19 0800 862 0453

TROUBLESHOOTING GUIDE

WARNING: To reduce the risk of shock and unintended operation, turn o

power and remove power pack before servicing.

Vacuum is not picking up debris, no suction or light suction.

(Refer to Maintenance section for more information.)

• Check ﬁlters to see if they need cleaning. Follow instructions for rinsing and completely

air-drying the ﬁlters before reinserting in the vacuum.

• Dust cup may be full; empty dust cup.

• Check ﬂoor nozzle for blockages; clear blockages if required.

• Remove any string, carpet ﬁbres, or hair that may be wrapped around the brushroll and Soft Roller

or trapped behind the Soft Roller.

• Check connection between handvac and wand for blockages; clear blockages if required. If the

issue persists, please contact Customer Service at 0800 862 0453

Vacuum lifts rugs.

• Check that vacuum is in EXTENDED RUNTIME mode. Take care when vacuuming rugs with

delicately sewn edges.

• Turn off the unit to disengage the brushroll and restart with the Power button.

Brushroll/Soft Roller does not spin.

• If Brushroll Indicator Light on the ﬂoor nozzle turns red, the brushroll and/or Soft Roller have

stopped spinning. Immediately turn off and remove Lithium ION Power Pack from handheld vacuum

and remove blockage before reconnecting and turning vacuum back on. If light turns green, the

blockage has been successfully cleared. If it remains red, please contact Customer Service at 0800

862 0453.

• If headlights are not illuminated, there is a connection issue between the handheld vacuum, wand,

and nozzle. Try disconnecting and reattaching the pieces. If the headlights still do not illuminate,

please contact Customer Service at 0800 862 0453.

Vacuum turns o on its own.

There are several possible reasons for the vacuum turning off on its own, including blockages, Lithium

ION Power Pack issues, and overheating. If vacuum turns off on its own, perform the following steps:

1. Check LED lights on Lithium ION Power Pack to see if it needs to be recharged. If power pack

does not need charging, turn off vacuum and remove power pack.

2. Empty dust cup and clean ﬁlters (see Maintenance section).

3. Check wand, accessories, and inlet openings and remove any blockages.

4. Allow unit and Lithium ION Power Pack to cool for at least 45 minutes, until it returns to room

temperature.

5. Return power pack to vacuum and press Power button.

Note: If vacuum still does not operate properly, contact Customer Service at 0800 862 0453.

LED lights on ION Power Pack are ﬂashing.

• If top 2 or bottom 2 LED lights are ﬂashing (Fig. A, Fig. B), call Customer Service at

0800 862 0453.

• Bottom LED light is ﬂashing (Fig. C): Lithium ION Power Pack needs to be charged.

• Top and bottom LED lights are ﬂashing (Fig. D): Lithium ION Power Pack temperature is not optimal,

so charging is temporarily paused. Leave power pack plugged in and charging will resume soon.

Fig. A Fig. B Fig. C Fig. D

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Shark IF250 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Shark IF250

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info