Bedienungsanleitung Shark NV650 SERIES Rotator (Seite 5 von 6) (Englisch, Französisch, Spanisch)

668630

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

PRECAUTIONARY MEASURES

OPERATING INSTRUCTIONS

Important: If the suction opening of the hose is BLOCKED, switch off the vacuum

cleaner and remove the blocking substance before you start the unit

again.

Fig. 11

6. Vigorously “TapClean”

the HEPA Dust Cup

Filter on a hard

surface until no more

dust is observed

falling out from

between the pleats of

the filter. (fig. 11)

Fig. 12

Debris

Screen

7. “TapClean” the Debris

Screen or rinse under

a faucet until clean.

(fig. 12) Remember

that the Debris Screen

must be completely

dry before reinstalling

in the vacuum.

8. Replace the Debris Screen on the

HEPA Dust Cup Filter and reinstall

filter assembly in the vacuum. (not

shown)

CAUTION: The suction hole must be

open, free of any obstructions at all

times. Otherwise, the motor will overheat

and could become damaged.

PLEASE NOTE: The white pleated

filter material in the HEPA Dust Cup

Filter will discolor over time -This is

NORMAL and will NOT affect the

performance of the filter. If the HEPA

Dust Cup Filter

is properly

"TapCleaned”

after each use

and suction

does not return

to 100%, then

we suggest that

the HEPA filter

be “TapCleaned”

vigorously until no

more dust can be removed, then

rinsed under the faucet and allowed to

dry for 24 hours before refitting into

the vacuum. (Fig. A) This should be

done once a month or when

suction appears reduced.

Fig. A

Wash once a

month or when

suction

appears

reduced.

Warning: Allow 24

hours for drying before

replacing in unit.

Cleaning & Changing the

HEPA Dust Cup Filter cont.

IMPORTANT: This unit is equipped

with a motor protective thermostat. If

for some reason the vacuum cleaner

should overheat, the thermostat will

automatically turn the unit off. Should

this occur:

• Push the On/Off button once.

• Disconnect the plug from the

power source.

• Check the source of overheating

problem. (i.e. clogged hose or

filter)

• If clogged hose or filter is found,

unclog the hose and replace the

filters.

• Wait at least 45 minutes before

attempting to reuse the vacuum.

• After unit has cooled down for

45 minutes, plug in the cleaner

and push the On/Off button. The

vacuum should start again.

• If the vacuum still does not start,

contact customer service at

1-800-798-7398.

Motor Thermostat

4. When pulling out the power plug

from the wall outlet, pull the plug

not the power cord.

1. Do not operate the vacuum

cleaner too close to heaters or

radiators.

2. Before inserting the power plug

into the wall outlet, make sure that

your hands are dry.

3. Before you start vacuuming,

make sure to remove large or

sharp objects that might

damage the HEPA Filter.

5. Do not pick up anything that is

burning or smoking such as

cigarettes, matches or hot ashes.

6. Do not use without HEPA filter in

place.

7. Do not bend, trample or pull the

hose by force. Do not operate with a

damaged hose.

8. When vacuuming fine dust particles

such as gyproc dust, flour or any

other fine dust, empty the dust cup

and "TAPCLEAN

" the dust cup

filter frequently to avoid over heating

the motor.

6 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Shark NV650 SERIES Rotator Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info