Bedienungsanleitung Sharp 25N-S100 Operation Manual (Seite 33 von 40) (Englisch)

13183

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

L To watch video material playback.

• Press the Remote’s

INPUT

to select VIDEO INPUT mode to which the video equipment you want to

playback is connected.

• The external VIDEO INPUT mode will change as follows each

time the

INPUT

is pressed.

• INPUT mode can be selected by pressing either the

CH UP

(

) on the TV remote control when the

TV is set to the highest channel stored in memory, or by pressing the

CH DOWN

(

) when it is set to

the lowest channel.

• When connecting video or audio equipment to the television, be sure that the power is turned off in

order to prevent damage to either the television or the equipment being connected.

• The S-VIDEO terminal has priority over a VIDEO terminal (IN-1). When you want to watch pictures

from video equipment connected to a VIDEO terminal, unplug equipment connected to the

corresponding S-VIDEO terminal.

• It is the intent of SHARP that this product be used in full compliance with the copyright law and that

prior permission be obtained from copyright owners whenever necessary.

• For detailed information on the connection and use of auxiliary equipment, refer to the instruction

manuals of the equipment being used.

• The connection cords can be obtained from your local video store.

NOTE:

Using the Audio Output Jacks (25N-S180 and 27N-S180 only)

L These jacks are used for connecting a standard stereo amplifier. Control of STEREO/MONO/

SAP, VOLUME and MUTE are retained at the TV. These jacks relay the audio signal of all

programs being displayed on the TV screen.

(AUDIO OUTPUT JACKS are located on the rear of the cabinet.)

CONNECTIONS

(1) Before connecting the

cord, turn on the TV and

adjust the VOLUME

control on the TV for a

moderate listening level.

(2) Turn off the TV and

connect the audio cord to

the AUDIO LINE OUTPUT

JACKS on the TV.

(3) Turn the TV set and stereo

amplifier on.

(4) If you desire, you can

turn off the sound to the

TV’s internal speakers by

SPEAKER mode. See

page 13 - 14.

(5) Adjust the VOLUME

control on the stereo

amplifier for a moderate

listening level.

(6) Control of the audio can be done using the audio controls (STEREO/MONO/SAP, VOLUME, and

MUTE), from either the remote control, or directly from the TV set.

• For detailed information on the connection and use of auxiliary equipment, refer to the operation

manuals of the equipment being used.

• When connecting monaural equipment to the AUDIO INPUT or OUTPUT of this set, use an audio

connection cord and plug adapter as shown below.

• For optimal sound quality, it is recommended to keep the TV’s audio output level high.

(Rear connection

terminals of TV)

To the TV

Pin plug x 2

Pin plug

Plug adapter

To the equipment

being connected

Pin jack/Mini plug

NOTE:

Using the Video and Audio Input Jacks (Continued)

32-40 25&27NS100/180 1.4 6/1/00, 2:12 PM33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp 25N-S100 Operation Manual Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info