Bedienungsanleitung Sharp AR235 (Seite 19 von 130) (Englisch)

17539

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

POWER ON AND OFF

GETTING STARTED

Initial settings

The copier assumes the initial settings when it is first turned on, when the CLEAR ALL key is pressed,

or a preset time (auto clear time) after the last copy is made in any mode. The initial settings that

appear in the display are shown below.

●

Copy ratio: 100%

●

Exposure: Automatic

●

Auto paper selection: On.

●

Paper feed station: Paper tray 1 (At power on, the previously selected paper tray will again be

selected.)

●

Copy quantity: 0

●

All special copier modes: Off

★KEY OPERATOR The auto clear time can be changed. See page 15 of the KEY OPERATOR'S

GUIDE.

Power save modes

The copier has two power save modes to reduce overall power consumption and thereby reduce the

cost of operation and to conserve natural resources to help reduce environmental pollution. The two

power save modes are preheat mode and auto power shut-off mode.

★ KEY OPERATOR

The time to enter the preheat and auto power shut-off modes have been preset at the factory to 15 min.

for the preheat mode and 60 min. for the auto power shut-off mode. These times can be changed as

described in the key operator's guide. It is suggested that you set appropriate times according to the

actual usage of the copier.

Preheat mode

The copier will enter the mode once the set time has elapsed without any copier operation after the last

copy of a run is made or power is turned on and no copier operations have been made.

When the copier enters the preheat mode, the backlight of the display will be turned off. In this condition,

the fuser in the copier is maintained at a lower heat level thereby saving power. The preheat level is,

however, high enough to allow the copier to come to a ready condition or begin copying approximately

10 seconds after any key input is made.

To copy from the preheat mode, make desired copier selections and press the START key using the

normal copying procedure.

★

★★

★KEY OPERATOR See page 16 of the KEY OPERATOR'S GUIDE for information on setting the

preheat mode.

Auto power shut-off mode

If the auto power shut-off mode is enabled, the copier will enter the mode once the set time has elapsed

without any copier operation after the last copy of a run is made or the power is first turned on and no

copier operations have been made.

When the copier enters the auto power shut-off mode, the displays and all the indicators except the

mode indicators will be turned off. In this condition, the fuser in the copier will be turned off.

To turn the power back on, press the COPY key or another mode key that is lit. You can make desired

settings and press the START key after warm-up starts.

★

★★

★KEY OPERATOR See page 15 of the KEY OPERATOR'S GUIDE for setting the auto power shut-off

timer. See page 20 of the KEY OPERATOR'S GUIDE for enabling or disabling the auto power shut-

off.

Ready to copy.

100%

AUTO

00.book 17 ページ２００１年４月２０日金曜日午後９時３４分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp AR235 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp AR235

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info