Bedienungsanleitung Sharp ARM160 (Seite 61 von 96) (Englisch)

26400

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

TROUBLESHOOTING

Poor scanning quality.

The document glass or the underside of the document

cover/SPF/RSPF is dirty.

→ Clean regularly.

Original smudged or blotchy.

→ Use a clean original.

–

You have not specified a suitable resolution.

→ Make sure that the resolution setting in the scanner driver is

appropriate for the original.

–

You are scanning a large area (for example an entire 11" x

17") at high resolution.

→ If you attempt to scan a large area at high resolution and there is

insufficient memory in the machine to hold the scanned data,

scanning will take place at a lower resolution and the scanner

driver will enhance the data to make up for the lower resolution.

However, the quality of the enhanced image will not be as high as

if scanning took place at the higher resolution. Use a lower

resolution setting, or scan a smaller area.

–

You have not specified a suitable value for the "B/W

Threshold" setting.

→ If you are scanning with a TWAIN-compliant application and are

using "White", "Red", "Green" or "Blue" mode from "Light Source"

menu, make sure that a suitable value is specified for the "B/W

Threshold" setting. A larger threshold value makes your output

darker, while a small threshold value makes it lighter. To adjust

the threshold automatically, click the "Auto Threshold" button on

the "Image" tab of the "Custom Settings" screen.

–

The brightness and contrast settings are not suitable.

→ If you are scanning with a TWAIN-compliant application and the

resulting image has unsuitable brightness or contrast (for

example it is too bright), click the "Auto Brightness/Contrast

Adjustment" button on the "Color" tab of the "Custom Settings"

screen. Click the "Brightness/Contrast" button to adjust the

brightness and the contrast while viewing the scanned output

image on the screen. If you are scanning with a WIA-compliant

application or the "Scanner and Camera Wizard", click "Adjust

the quality of the scanned picture" or the "Custom settings"

button, and adjust the brightness and contrast in the screen that

appears.

–

The original is not placed face up in the SPF/RSPF or face

down on the original table.

→ Place the original face up in the SPF/RSPF or face down on the

original table.

18, 19

The original was not placed in the correct position.

→ Place the original correctly.

18, 19

"Quick Scan" has been selected.

→ If scanning is performed when the "Quick Scan" option has been

selected, image quality may be degraded. This is because the

scanned data is transferred using JPEG compression. If image

quality is poor, then perform scanning again without selecting the

"Quick Scan" option. ("Quick Scan" is not selected by default.)

–

Problem Cause and solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp ARM160 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp ARM160

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info